|
|
|
Kto jest w sklepie?
Sklep przegląda 5398 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
XG-V10XE
ADJUSTING THE PC INTERFACE (CPCi-0042CE12. PC I/F Unit)
1. Initializing the EEPROM
1) Press S2601 to call the process mode. 2) Execute the S1 command on the SSS menu. (The S1 command is used to get the PC boards initialized. Do not carry out the S2 command because otherwise all the other adjustment data than on the PC boards would be initialized.) 3) Make sure the program version VER.XXX on the SPECIAL menu is the latest one.
2. Adjusting the levels
2-1. Preparing the oscilloscope 1) Set the oscilloscope range to 1 Vdc/div. and 5 µs/div. 2-2. Connecting the PC interface 1) Connect the PC interface to the set and make sure the P8404, P8405 and P8502 connectors are all tight in position. 2) Connect a cable between the ANALOG OUTPUT terminal (signal generator) and the DSUB connector (projector's INPUT1). 3) Set the projector's INPUT SELECT to the INPUT1 position. 4) Set the signal generator to the XGA mode (1024 x 768, 60 Hz, 32 tones). Adjust the output amplitude between the black and white levels to 700 mVp-p (terminated with a 75-ohm impedance). 5) Turn on the power. 2-3. Adjusting and checking the levels 1) Press S2601 and call the process mode. 2) Adjust the SH-PHASE setting on the OUPUT3 menu to 8. (Make sure the onscreen display characters appear crisp and clear.) (Adjusting the A/D menu settings) 3) G-BRIGHT adjustment: Feed the black signal and adjust the G-BRIGHT setting on the A/D menu until there are bit dropouts. With the above adjustment completed, get the setting 4 points up. 4) R-BRIGHT adjustment: Feed the black signal and adjust the R-BRIGHT setting on the A/D menu until there are bit dropouts. With the above adjustment completed, get the setting 4 points up. 5) B-BRIGHT adjustment: Feed the black signal and adjust the B-BRIGHT setting on the A/D menu until there are bit dropouts. With the above adjustment completed, get the setting 3 points up. 6) G-D adjustment: Feed the white signal and adjust the G-D setting on the A/D menu until there are bit dropouts. 7) R-D adjustment: Feed the white signal and adjust the R-D setting on the A/D menu until there are bit dropouts. 8) B-D adjustment: Feed the white signal and adjust the B-D setting on the A/D menu until there are bit dropouts. 2-4. Adjusting the DTV settings 1) Feed the 480P Y signal to the INPUT1 terminal. Keep out the R (Pr) and B (Pb) signals. 2) G-BRIGHT adjustment: Adjust the G-BRIGHT setting to the same as that on the A/D menu. Then get the setting 2 points up. 3) CR-OFFSET adjustment: Adjust the CR-OFFSET setting to 16. 4) CB-OFFSET adjustment: Adjust the CB-OFFSET setting to 16. 5) Press S2601 to exit from the process mode.
35
|
|
|
> |
|
