|
|
|
Kto jest w sklepie?
Sklep przegląda 5956 gości i
40 zarejestrowanych klientów |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
(V)
V1
CLV
0V
60Hz
50Hz
a
V2 Pulse ON time 0V
CPU output (CLPWM)
(msec)
�
V3
The shorter the pulse ON time is, the higher the CLV is, and vice versa. The pulse ON time rises at the zero-cross timing of AC and is driven with duty. Positive pulses the copy lamp ON signal are generated by C248 (C253) at falling of the CPU output and inputted to the photo triac through the 2-stage transistors.
�
0V
�
b
+5V
(11) Power section
This model is provided with the auto shut-off mode. The power section is also designed for it. When the power switch of the copier is turned on and the AC power is supplied, AC waveforms for +5V power are generated in the secondary side of transformer T301. The AC waveforms are full-wave-rectified and smoothed by diode BD102 on the main PWB side, and 5V is generated by 3-terminal regulator of IC111. The 5V power is supplied to the CPU. When the CPU is actuated by the 5V power, it starts the switching power to output the SWPEN signal (CPU output: LOW). The switching power outputs voltages of 24V and VBS with this signal. BVS is stabilized by IC112 to become a voltage with stable BV, and is used for LED display. 24V is supplied to the motor and the solenoid, and supplied also to the 3-terminal power for 5V through D144. When the CPU turns off SWPEN to enter the auto power shut-off mode, 24V and VBS output falls near zero, virtually turning off.
V4 0V
V5
0V
VCL
0V
Main switch (MSW)
T301
Main PWB
BD102 SINB60
IC111 7805
5V C107 47µF
C111 2200µF
* At rising of the CLPWM signal (V4), the coy lamp is switched by the triac. The trigger signal Cl is sent to the triac to turn on the lamp. Then the lamp is turned off at the zero-cross point of V1 waveform. The CPU reads the control voltage level (QV) corresponding to the change in the copy lamp voltage The CLV produces the waveform equivalent to the copy lamp voltage waveform which disables the full-rectified waveform of AC input during the pulse ON time. The waveform is converted to the DC level by the low pass filter composed of C102 and R105, and inputted to the CPU. The relationship between the CLV and the pulse ON time is shown in the figure below.
AC PWB
DC power unit
24V
D144 1N4004E
GND V8S IC112 7808 5V
1SWPEN
8V C105 47µF
IC101 CPU
DTC123JKA
C106 47µF
8 or 10 msec
Q209
Pulse ON (Varies)
12 � 10
 $4.99 Z-830 SHARP
Katalog Części Katalog części w formie pliku PDF. Plik zawiera wykaz części znajdujących się w urządzeniu wr…
|
|
|
> |
|
