FENDER 226800-6900
Instrukcja Obsługi

Rear Panel Functions
� NOTE: Item 5 applies only to the Stage 100. 5. EXTERNAL SPEAKER (8� minimum) - Use this output jack when one 8� speaker enclosure is to be connected to the Stage 100 for additional output. The Stage 100�s internal speaker must be connected while using this jack. 6. LINE OUT - This balanced XLR line-level output is designed for connection to an external power amplifier or main house mixer. The signal from this output jack includes all tone shaping done by the amplifier. 7. RETURN - This 1/4 inch, unbalanced, TS, linelevel input jack is designed to accept a signal from external effects devices or another amplifier in a �daisy-chain� configuration. 8. SEND - This 1/4 inch, unbalanced, TS, line-level output jack is designed to feed the preamp signal to external effects devices or to an �add-on� amplifier in a daisy-chain configuration. 9. FOOTSWITCH - Connect the footswitch at this jack. The two-button footswitch enables switching between Normal and Drive channels and ON/OFF switching of the MORE DRIVE pre-amplifier boost. Using this jack disables these switching functions from the front panel. NOTE: Connecting the footswitch with an unshielded speaker type cord is preferable to using a shielded coaxial guitar cord.

1 34 2
STAGE 100H SPEAKER JACKS

5
STAGE 100 SPEAKER JACK

6789

1. POWER SWITCH - Turns the AC power ON and OFF. 2. LINE CORD - This amplifier is equipped with an IEC grounding type supply cord to reduce the possibility of shock hazard. Be sure to connect it to a grounded AC receptacle in accordance with the voltage and frequency ratings listed on the rear panel under INPUT POWER. � NOTE: Items 3 and 4 apply only to the Stage 100H. 3. SPEAKER OUTPUT (8� minimum) - Use this output jack when only one 8� speaker enclosure is to be connected to the Stage 100H. If two 8� speaker enclosures are to be connected, use both parallel speaker output jacks (total load of 4�). 4. SPEAKER OUTPUT (4� minimum) - Use this output jack when one 4� speaker enclosure is to be connected to the Stage 100H. (Using this jack internally switches the Stage 100H to accept a 4� load.)

Specifications
TYPE: PART NUMBER: Stage 100 (combo) PR 401 22-6700 (120V, 60Hz) US 22-6730 (240V, 50Hz) Aust 22-6740 (230V, 50Hz) UK 22-6760 (230V, 50Hz) Eur 22-6770 (100V, 50/60Hz) Jpn 400W 100W RMS into 8� @ 5%THD 160W RMS into 4� @ 5%THD INPUT 1: 850k�, INPUT 2: 66k� 1k� 10k� 810mV for 160W into 4� @1kHz 620mV for 100W into 8� @1kHz 4A125V for 100V / 120V ver 2A250V for 230V / 240V ver 2 Button - (P/N 050419) Normal/Drive, Drive/More Drive One 8� Celestion G12T-100 12� speaker (P/N 054420) 17.5 in. (45 cm) 22.4 in. (57 cm) 10.2 in. (26 cm) 42 lbs. (19.1 kg) Stage 160 (combo) PR 400 22-6800 (120V, 60Hz) US 22-6830 (240V, 50Hz) Aust 22-6840 (230V, 50Hz) UK 22-6860 (230V, 50Hz) Eur 22-6870 (100V, 50/60Hz) Jpn 400W 160W RMS into 4� @ 5%THD N/A INPUT1: 850k�, INPUT 2: 66k� 1k� 10k� 810mV for 160W into 4� @1kHz N/A 4A125V for 100V /120V ver 2A250V for 230V / 240V ver 2 Button - (P/N 050419) Normal/Drive, Drive/More Drive Two 8� Celestion G12T-100 12� speakers (P/N 054420) 18.5 in. (47 cm) 26.1 in. (66 cm) 10.3 in. (26 cm) 53 lbs. (24.1kg) Stage 100H (head only) PR 453 22-6900 (120V, 60Hz) US 22-6930 (240V, 50Hz) Aust 22-6940 (230V, 50Hz) UK 22-6960 (230V, 50Hz) Eur 22-6970 (100V, 50/60Hz) Jpn 400W 100W RMS into 8� @ 5%THD 160W RMS into 4� @ 5%THD INPUT1: 850k�, INPUT 2: 66k� 1k� 10k� 810mV for 160W into 4� @1kHz 620mV for 100W into 8� @1kHz 4A125V for 100V /120V ver 2A250V for 230V / 240V ver 2 Button - (P/N 050419) Normal/Drive, Drive/More Drive N/A 8.5 in. 22.4 in. 9.5 in. 24 lbs. (22 cm) (57 cm) (24 cm) (10.9 kg)

POWER REQUIREMENTS: POWER OUTPUT: (WITH EXTENSION SPEAKER): INPUT IMPEDANCE: FX SEND OUTPUTIMPEDANCE: FX RETURN INPUT IMPEDANCE: POWER AMPIN SENSITIVITY: FUSE: FOOTSWITCH: SPEAKER COMPLIMENT: DIMENSIONS: WEIGHT: HEIGHT: WIDTH: DEPTH:

Product specifications are subject to change without notice.

5