|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
32JF-73E
� Use the channel up and down buttons to move between the options. � Use the volume control buttons to change the data. � To store the data, use the stand-by button on the remote control. � To exit the Service Mode, turn the receiver off using the mains switch. When the Service Mode is entered the following On Screen Display appears SERVICE SOFTWARE �����x�� SW on: XXXX SW off: XXXX Hours ON: XXXX The figures displayed in the �XXXX� locations are hexadecimal representations of the number of times that particular function has been executed. For example if the hexadecimal number displayed after �SW on� was 0E4A, this would correspond to the receiver being turned on 3658 times. The figure displayed in the � �����x�� � location is the EPROM version. X
Adjustment menu:
The following adjustments can be carried out in the Service Mode. 01. Horizontal Shift 02. East West Width 03. Pin Phase 04. Pin Amp (Amplitude) 05. Corner Amplitude 06. Corner Symmetry 07. Vertical Linearity 08. Vertical Angle 09. Vertical Bow 10. Vertical Amplitude 11. S Correction 12. Vertical Shift 13. Red Gain 14. Green Gain 15. Blue Gain 16. Red Cut Off 17. Green Cut Off 18. Blue Cut Off 19. Alter NVM Pag (Page) 20. Alter NVM Pos (Position) 21. Alter NVM Val (Value) 22. Teletext Mix Mode Contrast 23. Teletext Contrast 24. OSD Contrast 25. DVCO Adjustment (Only PAL) 26. DVCO Adjustment (Only NTSC) 27. AGC Adjustment 28. Rotation Inspection 29. Auto Installation On/Off
When in the Service Mode it is possible to access certain functions by using the teletext keys as below. � By pressing the Blue button each adjustment can be directly accessed via the remote control. Referring to the list above, press the Blue button followed by the adjustment number, this will directly access the selected adjustment. If any number above 29 is selected, the set will revert to the Service Mode entry page. To access a number less than 10, use the 0 key first, i.e. 02. � Press the Yellow button to go straight to the AGC adjustment. � Press the Green button once to enter �FACTORY VOLUME� level. Use volume control keys to change the setting. The original value will be recovered after resetting the TV set. � Press the Green button twice to enter �FACTORY BALANCE� level. Use volume control keys to change the setting. The original value will be recovered after resetting the TV set. � Press the Green button three times to enter �FACTORY BASS� level. Use volume control keys to change the setting. The original value will be recovered after resetting the TV set. � Press the Green button four times to enter �FACTORY TREBLE� level. Use volume control keys to change the setting. The original value will be recovered after resetting the TV set. � Press the Red button once to enter �FACTORY CONTRAST� level. Use volume control keys to change the setting. The adjustment is stored automatically. � Press the Red button twice to enter �FACTORY BRIGHTNESS� level. Use volume control keys to change the setting. The adjustment is stored automatically. � Press the Red button three times to enter �FACTORY COLOUR� level. Use volume control keys to change the setting. The adjustment is stored automatically. � If buttons 0 through 9 are pressed, the set will automatically go to that program number. � By pressing the Menu button, the unit will normalise Picture and Audio settings. The Auto Installation is then turned �on�.
7
|
|
|
> |
|
