|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
CONVERGENCE ADJUSTMENT
Adjust convergence from center to circumference in order. KEY FUNCTION IN THE CONVERGENCE ADJUSTMENT: Up : Selet Green color: Left : Blinking of cursor ON/OFF: Right: Adjust mode ON/OFF: Down: Erase Green line: Erase Red line: Erase Blue line: 2 button 3 button 4 button 5 button 6 button 7 button 8 button 0 button 100 button CHRTN (ENT) button
1. Select the adjustment mode following the steps on page 9 of original servicemanual. RCUT 40H
2. Press �7� button to display the built-in cross-hatch pattern.
Cursor
Note: Adjusting procedure in replacing convergence board. 1. User convergence center check. Make sure the best convergence setting is about the center of adjustable range. 2. CENTERING ADJUSTMENT 3. PICTURE POSITION ADJUSTMENT 4. HIT, WID ADJUSTMENT 5. CONVERGENCE ADJUSTMENT
21.5 (43") 26.5 (50") 28.5 (53", 55") 31.0 (61") P= 43.7 �14 (43") 50.5 �14 (50") 55.8 �14 (53", 55") 62 �14 (61")
21.5 (43") 26.5 (50") 3.5 (43", 50") P= 72.2 �12 (43") 3.5 (43", 50") 28.5 (53", 55") 4.0 (53", 55") 84.0 �12 (50") 4.0 (53", 55") 31.0 (61") 5.0 (61") 92.5 �12 (53", 55") 5.0 (61") 102.5 �12 (61")
The pattern includes three control (R, G, B). The cursor should be blinking in Red. This means that the Red color is adjustable. Adjustment around cursor can be done. 3. Press �3� button to select Green color to be adjusted. 4. Press �5� button to stop the blinking of cursor. 5. Press �2 (up)�, �8 (down)�, �4 (left)� or �6 (right)� to obtain the correct cross-hatch pattern as above. If necessary, the specified color line can be erased from the screen. 100 button ...................... to erase Red line 0 button ...................... to erase Green line RTN button ...................... to erase Blue line 6. Press �5� button to make the cursor blinking. 7. Press �2�, �8�, �4�, �6� buttons to move the cursor to other point to be adjusted. 8. Repeat steps 4 to 7. 9. Repeat steps 3 to 8 to adjust Red and Blue colors. Converge the selected color line into the Green line. 10. Press �7� button to memorize the adjusted states. At this time, picture changes for about 1 second. 11. Press �7� button again to return to the normal picture.
�3�
|
|
|
> |
|
