|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
FIRMWARE RENEWAL MODE
1. Turn the power on and press [SELECT] button on the remote control unit to put the TV/DVD/VCR into DVD mode. Then remove the disc on the tray. (It is possible to move to F/W version up mode only when the TV/DVD/VCR is in DVD mode with the tray open.) 2. To put the TV/DVD/VCR into F/W version up mode, press [9], [8], [7], [6], and [MODE] buttons on the remote control unit in that order. Fig. a appears on the screen.
"*******" differs depending on the models. "*******" differs depending on the models.
F/W Version Up Mode VERSION : Completed SUM : 7ABC
Model No : ******* VERSION : *.** ************.ab7
(*2)
Fig. c Completed Program Mode Screen
F/W Version Up Mode
Model No : ******* VERSION : *.**
At this time, no button is available. 6. Remove the disc on the tray. 7. Press [SELECT] button on the remote control unit to go to TV mode, or press [POWER] button on the unit to turn the power off. 8. Press [SELECT] button on the remote control unit to put the TV/DVD/VCR into DVD mode again. 9. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. d appears on the screen.
"*******" differs depending on the models.
Please insert a DISC for F/W Version Up.
EXIT: SELECT
Fig. a Version Up Mode Screen
The TV/DVD/VCR can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open. 3. Load the disc for version up. 4. The TV/DVD/VCR enters the F/W version up mode automatically. Fig. b appears on the screen. If you enter the F/W for different models, �Disc Error� will appear on the screen, then the tray will open automatically.
"*******" differs depending on the models.
MODEL : ******* Version : *.** Region : *
EEPROM CLEAR : CLEAR
EXIT: SELECT
F/W Version Up Mode VERSION : Reading...
Model No : ******* VERSION : *.** ************.ab7
Fig. d
10. Press [CLEAR] button on the remote control unit. Fig. e appears on the screen.
"*******" differs depending on the models.
(*1)
MODEL : ******* Version : *.** Region : *
Fig. b Programming Mode Screen
EEPROM CLEAR : OK
The appearance shown in (*1) of Fig. b is described as follows: No. 1 2 3 Appearance Reading... Erasing... State Sending files into the memory Erasing previous version data
EEPROM CLEAR : CLEAR
EXIT: SELECT
Fig. e
Programming... Writing new version data
When �OK� appears on the screen, the factory default will be set. Then the firmware renewal mode is complete. 11. To exit this mode, press [CH. o / p] or [SELECT] button to go to TV mode, or press [POWER] button to turn the power off.
5. After programming is finished, the tray opens automatically. Fig. c appears on the screen and the checksum will be shown in (*2) of Fig. c.
1-9-1
T1200FW
|
|
|
> |
|
