English
Controls (see 1)
Controls
Power supply
Clock
1 2 �
Radio
7
CD Player
To switch off radio and back to standby, press POWER. � The display lights off. To improve reception: FM: Extend and adjust the pigtail for optimum reception. MW: Uses a built-in antenna. Direct the antenna by adjusting the position of your unit. This set complies with the radio interference requirements of the European Community.
1 REPEAT ALARM � pushes to switch off alarm for a 6-minute period 2 LCD Display � shows the clock/ alarm time or CD/radio information 3 POWER � switches the set on or to standby � stops the active buzzer, radio or CD alarm for 24 hours � switches off the sleep timer 4 ALARM 1/ ALARM 2 � sets and activates alarm of ALARM 1 /ALARM 2 � stops the active buzzer, radio or CD alarm for 24 hours 5 CLOCK � sets clock time 6 SHUF/REP � selects different CD play modes: e.g. REPEAT or SHUFFLE (random order) 7 �/ § � adjusts clock / alarm time � skips CD tracks/ searches for a particular passage 8 9 � stops CD playback 9 0 ! @ # $ % ^ � erases a CD program ); � starts/ pauses CD playback PROG � programs CD tracks LIFT TO OPEN � lift here to open CD door DISPLAY � displays CD tracks or radio information AUX � 3.5mm audio input jack TUNING � tunes to a radio station BAND � selects waveband: FM or MW SLEEP � switches on/off radio, CD for timer mode
( Power cord � connects to wall outlet ) Pigtail � FM antenna to improve FM reception ¡ Battery compartment � insert a 9 volt battery, typed 6F22 (not supplied) for clock memory backup
Insert the battery into the battery compartment for clock memory backup. Connect the power plug to the wall outlet. Replace the battery once a year, or as often as necessary. Batteries contain chemical substances, so they should be disposed of properly.
Power supply
1 Check if the power voltage as shown on the type plate on the base of the set corresponds to your local power supply. If it does not, consult your dealer or service center. Connect the power plug to the wall outlet. The power supply is now switched on and the numbers on the display shows 0:00.You will need to set the correct time. 3 To disconnect the set from the power supply completely, unplug from the wall outlet. The type plate is located on the bottom of the set. 2 3 4 5 1
Setting the clock
The clock uses 24-hour time format.You may set the clock from 0:00 if the set is disconnected from the wall outlet. Press and hold CLOCK until clock digit for hour flashes. � It will exit the clock setting mode without setting if there is 5-second inactivity. Press repeatedly, or hold down � / § to adjust the hours. Press CLOCK to confirm the hour setting. � The clock digits for minute flash. Press repeatedly, or hold down � / § to adjust the minutes. Press CLOCK to confirm the setting. Standby power consumption (clock mode) . . . . . . . . . . . . . . . . . . . .. . . . 1.5W
2
CD playback
This CD clock radio can play only audio discs including CD-R (CD-recordable), CD-RW (CD-rewritable). Do not try to play a MP3-CD, CD-ROM, CD-RW, CDI,VCD, DVD or computer CD. 1 2 Press POWER to switch on from standby. � The display lights up. Select CD source by pushing CD�RADIO�BUZZER to CD. � �CD� is displayed. 3 4 Lift the CD door to open. Insert a CD with printed side facing up, and close the CD door. � Flashing ---- is displayed briefly, then total CD track number. Press ); to start playback. To view CD track information, press DISPLAY. � The current track number is displayed for several seconds (See 3), then it will switch back to clock display. To adjust the sound, turn VOLUME. To interrupt, press );.To resume playback, press ); again. To stop playback, press 9.
Clock memory backup
When a power failure occurs, the complete clock radio will be switched off. When the power supply returns, the time display shows 0:00 and you will need to reset the correct time on the clock. To retain the clock time and the set alarm time(s) in the event of an AC power failure or disconnection, insert a 9 volt battery, typed 6F22 (not supplied) into the battery compartment.This will act as a clock memory backup. When powered by the battery, the time will not be illuminated on the clock display, and operation of the alarms, FM/ MW radio and CD are also impossible. As soon as the AC power supply returns, the display will indicate the correct time.
Radio
1 2 Press POWER to switch on from standby. � The display lights up. Select RADIO source by pushing CD�RADIO�BUZZER to RADIO (located on the side panel). � �TUNER� is displayed. Push BAND to FM or MW to select desired waveband. Turn TUNING to find your station. To adjust the sound, turn VOLUME. To view radio information, press DISPLAY. � The current waveband and frequency will be displayed for several seconds (See 2), then it will switch back to clock display. 5 6
3 4 5 6
7 8 9
� adjusts timer options for radio/CD playback & VOLUME � adjusts sound level * CD�RADIO�BUZZER � selects CD or radio sound source � selects CD radio, or buzzer or alarm mode
10 To switch off CD playback and back to standby, press POWER. � The display lights off.
