jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
Tekstowy podgląd strony 9 (kliknij aby zobaczyć)
· When not using the unit for an extended period, remove all
paper from the paper tray and store it in a dry place. If paper is left in the unit for an extended period, the paper will absorb moisture from the air, resulting in paper jams.
Window. And the following message will appear on the display panel.
· When adding new paper to the paper tray, remove the old
paper already contained in the tray, place it on top of the new paper. Then load it all into the paper tray. Placing new paper on top of the paper already contained in the tray may result in feeding two sheets at one time.
Load selected paper into bypass slot
2) Open the bypass tray to set paper, referring step 1 and 2 above. 3) Press the "START" button. The unit will start printing. When printing more than one page: The message described above will also appear when printing of the first page has been completed. Load the paper again for the next page, and then press the "START" button. Repeat this process for each page. (For printing only) When loading an envelope Open the bypass tray until it reaches position 2 (the tray has two stop positions), set the paper knob to the "Thick Paper"setting. Load the envelope print side up with the flap to the right, and position against the right edge of the tray as shown bellow.
· The original image must be smaller than the paper in the
tray. If the original image is larger than the paper, this may cause smudges on the edges of the output and may make the machine dirty inside.
9. LOADING THE BYPASS TRAY WITH PAPER
If you wish to print on banner paper or another paper type not loaded into the main paper tray, use the bypass feed. Only one sheet of paper (or up to 5 sheets of banner paper (only for printing)) can be placed in the bypass tray at a time. 1. Open the bypass tray located on the rear of the unit.
Position 1
Position 2
2. Load the paper so that the side to be printed or copied onto is face up. Align the paper with the right side of the bypass tray.
(For printing only) When loading banner paper Open the bypass tray until it reaches position 2, and set the paper along the right side edge of the tray.
Note:
· Maximum 5 sheets of banner paper can be used. · When printing onto banner paper, be sure to use an application software supporting banner paper.
To use the bypass tray in the copy mode
To use the bypass tray in the copy mode, follow the steps shown below. 1) Open the bypass tray to set paper, referring step 1 and 2 above. 2) Press the "START" button. Paper will be automatically fed into the unit to be copied. You cannot make multiple copies using the bypass tray. Set the paper knob to the "Thick Paper" setting when copying onto thick paper.
· The paper knob should always be set to the "Normal Paper" setting except while printing on thick paper.
· The original image must be smaller than the paper in the
tray. If the original image is larger than the paper, this may cause smudges on the edges of the output and may make the machine dirty inside.
To use the bypass tray in the printer mode
To use the bypass tray in the printer mode, follow the steps shown below. 1) Select the bypass tray as a paper source on the printer driver, and send the print job. For details of the printer driver setup, refer to "Printer Properties" in the Online Manual. "Please set a sheet of paper on bypass and press the START button" message will appear on the Print Status
10. INSTALLING THE SOFTWARE
This chapter provides you with information on how to install required software to use this unit with your computer. Information on how to use the Online Manual is also provided. The following terms are used in this chapter. CD-ROM Means the supplied CD-ROM with the AJ-6000 Series Software.
