|
|
|
Kto jest w sklepie?
Sklep przegląda 5872 gości i
25 zarejestrowanych klientów |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
SERVICE
Technical data
Failure codes
Whirlpool Europe Customer Service
AKZ 493/IX 8585 493 01000
28.05.2004 / Page 3 Doc. No: 4812 725 18449
Product Type All
Failure Code F01
Failure Type Temperature Probe
Test First check probe connection. If ok, disconnect the probe and measure its resistance (1000� + 3.75 x Temp ambient). If value is in range, change Antares / Capricorn. Check heating elements insulation (disconnect each heating element and check each terminal for continuity to GROUND). If there is no continuity, change Antares / Capricorn. Replace Capricorn or if applicable reprogram Antares EEPROM using SAM. If the problem persists, change Antares. First check connection between Capricorn and Scales. If connection is ok, connect a new Capricorn to the Scales and check if the appliance works correctly. Otherwise change Scales. First unplug the appliance, wait at least 10sec then reconnect. Verify that latch system works correctly (door has to be closed, motor has to run). If this happens, check the connection between Antares and door latch system. If it is ok, check micro switch functionality (door switch open if the door is open and latch switch open if the door is unlocked). If switches are ok, then change Antares. First check connection between Antares and door latch system. If it is ok, check door switch functionality (open circuit if the door is open, closed circuit if the door is closed). If switch is ok, then change Antares. First check connection between Antares / Capricorn & User Interface. If connection is ok, connect a new User Interface to the Antares / Capricorn and check if the appliance works correctly. In this case change the User Interface on the appliance. Otherwise change the Antares / Capricorn. Change G2 Smart. First check connection between Antares & User Interface. If connection is ok, connect a new G2SMART to the Antares and check if the appliance works correctly. In this case change the G2SMART on the appliance. Otherwise change the Antares First check grill connections. If it is ok, disconnect the heating element and check the resistance between the terminals (approx. 22� ± 3�). If the value is in range, change Antares. First check connection between G2 and TEX. If connection is ok, connect a new TEX to the G2SMART and check if the appliance works correctly. Otherwise change G2SMART
All
F02
Temperature Error
All
F03
A.M. EEPROM
Capricorn only
F04
W.I.S.P. Protocol
Pyro
F05
Door Latch
Pyro
F06
Door Closure
All
F07
Communication UI/AM
TAD TAD
F08 F09
UI EEPROM Communication G2SMART/Antares
Pyro
F10
Primary grill
TAD
F11
Communication G2SMART/TEX
|
|
|
> |
|
