|
|
|
Kto jest w sklepie?
Sklep przegląda 5696 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
 ;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
;
...instrukcja serwisowa w pełni czytelna i kompletna. Dziękuję!
SECTION 3 DISASSEMBLY
3.1 DISASSEMBLY PROCEDURE 3.1.1 REMOVING THE REAR COVER � Unplug the power plug. (1) As shown in Fig.2, take out the 14 screws [A]. (2) Remove the REAR COVER toward you. NOTE : When reinstalling the REAR COVER, carefully push it inward after inserting the chassis into the REAR COVER groove. 3.1.6 REMOVING THE SPEAKER � Remove the REAR COVER. � Remove the CHASSIS BASE. (1) As shown in Fig.2, take out the 4 screws [H]. (2) Follow the same steps when removing the other hand SPEAKER. 3.1.7 CHECKING THE MAIN PW BOARD � To check the backside of the MAIN PWB. (1) Pull out the CHASSIS BASE. (Refer to REMOVING THE CHASSIS BASE). (2) Erect the chassis vertically so that you can easily check from the backside of the MAIN PWB. CAUTION : � When erecting the chassis, be careful so that there will be no contacting with other PWB. � Before turning on power, make sure that the CRT earth wire and other connectors are properly connected. 3.1.8 WIRE CLAMPING AND CABLE TYING (1) Be sure to clamp the wire. (2) Never remove the cable tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.
3.1.2 REMOVING THE CHASSIS BASE � Remove the REAR COVER. (1) Slightly raise the both sides of the CHASSIS BASE by hand, and teka out the 2 claws [B] (Fig.1 and Fig.2) under the both sides of the chassis from the chassis rail. (2) As shown in Fig.1, draw the CHASSIS BASE backward along the chassis rail [C] (Fig.1) in the arrow direction [D] (Fig.2). (If necessary, detach the wire clamp, connector's etc.) NOTE : When conducting a check with power supplied, be sure to confirm that the CRT earth wire is connected to the CRT SOCKET PWB and the MAIN PWB.
3.1.3 REMOVING THE TERMINAL BOARD � Remove the REAR COVER. (1) As shown in Fig.2, take out the 4 screws [E]. (2) When you pull out the TERMINAL BOARD, it can be removed.
FRONT CABINET
3.1.4 REMOVING THE FRONT CONTROL PW BOARD � Remove the REAR COVER. � Remove the CHASSIS BASE. (1) As shown in Fig.2, take out the 3 screws [F] attached the FRONT CONTROL PWB with the front cabinet. (2) Then remove the FRONT CONTROL PWB.
MAIN PWB
C
3.1.5 REMOVING THE FRONT TERMINAL PW BOARD � Remove the REAR COVER. � Remove the CHASSIS BASE. (1) As shown in Fig.2, take out the 2 screws [G]. (2) Then remove the FRONT TERMINAL PWB.
CHASSIS BASE
B
Fig.1
(No.52121)1-9
|
|
|
> |
|
