WHIRLPOOL AWM 8000-I
Instrukcja Obsługi

3GB15033a.fm Page 2 Friday, July 5, 2002 6:30 PM

CONSUMPTION DATA
Temperature Selector Programme White Cotton Coloured cotton Coloured cotton Coloured cotton Coloured cotton Easy Care/Synthetics Daily Load Rapid Delicates Wool Handwash (°C) 95 60 60 60 40 40 40 30 30 40 30 (kg) 8.0 8.0 3.5 1.0 8.0 3.5 3.5 3.5 2.5 2.0 2.0 (l) 80** 72 45 25 72 55 45 35 65 60 60 (kWh) 2.60 1.45 1.10 0.70 0.75 0.55 0.55 0.35 0.45 0.50 0.30 Load Water Energy Approximate programme duration* (hours : minutes) 2:20 2:00 1:15 1:00 1:55 1:15 1:00 0:30 0:50 0:35 0:31

� Press the button to set another spin speed. � If the spin speed �0� is selected, the final spinning is cancelled but intermediate spin peaks remain during rinse. The water is drained out only.

CHANGE THE PROGRAMME, TEMPERATURE, OPTIONS AFTER PROGRAMME START
1. Press the �Start/Pause� button to interrupt the programme. The light flashes. 2. Select the new programme (with temperature), any options and another spin speed if you want. 3. Press the �Start/Pause� button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.

START DELAY
The �Start Delay� allows to run the machine at the consumer�s convenience, for example at night when electricity is cheaper. � Select programme, temperature and options. � Press the �Start Delay� button to select the delay time by 1 to 23 hours; � Press the �Start/Pause� button. � The time delay indication disappears when the programme starts and it is replaced by the remaining time. � The number of hours preselected can later be reduced pressing again the �Start Delay� button. To cancel the �Start Delay�. � Turn the programme selector to the � � position. � Reselect the desired programme and options and press the �Start/Pause� button.

CANCEL A PROGRAMME BEFORE THE END
Press the �Reset� (�Annulla�) button. Any existing water is drained out before the door can be opened.

CHILD LOCK
Detailed information can be found in the instructions for use. The controls can be locked to avoid interference by children. 1. If the machine is off: Turn the programme selector knob from the �0� position to any programme. Do not press the �Start/Pause� button. Press the �Child Lock� button for 5 seconds. The �Child Lock� indicator lights up. Turn the programme selector knob to the OFF position � � again. 2. While a programme is running: Press the �Child Lock� button for 5 seconds. The child lock indicator will light up. Now, in spite of the programme selector knob being turned, no programme can be started or altered. However, a running programme can be stopped at any time (e.g. in an emergency), by turning the programme selector knob to � �. Attempts at changing during the running programme are signalled by the lamp flashing. The indicator light for the actual programme running goes on. To unlock the controls, the machine must either have a programme running or be in select mode. Press the �Child Lock� button for 5 seconds. The child lock lamp will go out.

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. * The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household conditions applicable at that time. **To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

PROGRAMME START
Turn on the tap and press the �Start/Pause� button. The pilot lamp of the �Start/Pause� button lights up. The indicator lamps shows the sequence reached in the programme. After starting the programme, the sequence indication runs from top to bottom through Prewash, Wash, Rinse, Spin. When a sequence of the programme is finished the corresponding lamp goes out.

ADD DETERGENT, CLOSE THE DOOR AND SELECT THE PROGRAMME
Add the detergent as described in the programme table or in the chapter �Detergent and Additives� of the instructions for use. 1. Turn the programme selector knob to the desired programme. 2. The remaining time display shows the duration of the chosen programme (in hours and minutes) and the pilot lamp of the �Start/Pause� button lights up. 3. The programme sequence and the predefined spin speed indicators corresponding to the selected programme light up. The recommended temperature (see the indicator) can be altered by pressing the �+� or �-� button.

�Prewash� button � Only for heavily soiled laundry (e.g. sand, granular dirt). The cycle time increases approx. 15 minutes. �Intensive Rinse� button � More water and a longer time in rinse cycle is added. � This option is particularly suitable for areas with very soft water, for baby clothes and to help people with allergies. �Rinse Hold� button � The laundry remains in the last rinse water without being spun: this prevents creasing and colours from changing. � This option is particularly recommended for the programme �Synthetics� or �Delicates�. � This function is particularly useful if you want to postpone spinning to a later time, or if you want to drain only. Note: The programme starts to �Rinse Hold� as soon as the �Rinse Hold� indicator light in the programme display lights up. Terminate the �Rinse Hold� option: � Press the �Rinse Hold� button again; the programme will terminate automatically with the final spin cycle for the present wash programme. � If you do not wish to spin the clothes, turn the programme selector knob to the �Drain� programme and press the �Start/Pause� button again when flashing. �Spin Speed Reduction� button � Every programme has an automatic predefined maximum spin speed.

DOOR LOCK
After each programme start the door is locked and approx. 0.5 l of water is rinsed in. The door is unlocked for a few seconds. The door is then locked until the end of the programme. The door cannot be opened while the �Door Locked� indicator is on. Detailed information can be found in the instructions for use.

SELECT ANY DESIRED OPTION
Selecting any option the indication lights up. When the combination of programme, additional options and temperature is not possible, the indication lights switch off automatically and a signal sounds. �Easy Ironing� button � Can be used together with all programmes to reduce creasing. � Increases the water quantity and the clothes are spun very gently.

PROGRAMME END
� The time remaining is �0:00� and the �End�� light is on. 1. Turn the programme selector knob to the � � position. 2. Turn the tap off and leave the door ajar to allow the drum to dry out.

Whirlpool is a registered trademark of Whirlpool USA.

5019 301 15033/A
Black process 45.0° 100.0 LPI