PHILIPS AZ1016/97
Instrukcja Obsługi

English
Supplied Accessories
� AC power cord

Controls/Power Supply
Back panel (See 2)
^ Telescopic antenna - improves FM reception. & p � 3.5 mm stereo headphone socket Helpful hints: The speakers will be muted when headphones are connected to the set. * AC ~ - inlet for power cord. ( Battery door - open to insert 6 x 1.5V R-14/ UM2/ C-cells. ) Voltage selector � (inside the battery compartment, not all versions) adjust to match the local voltage 110/220V before plugging in the set.

Power Supply
� Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst: � Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type � � for the set. When inserting new batteries, do not try to mix old batteries with the new ones. Remove the batteries if the set is not to be used for a long time.

General Operation/Tuner
General operation
1 To select your sound source, adjust the Source selector to: CD, TUNER or TAPE/ OFF. 2 To switch off the set, adjust the Source selector to TAPE/ OFF position and check the cassette keys are released.

Top and front panels (See 1)
1 VOLUME � adjusts volume level. 2 BASS BOOST � turns the bass enhancement on/off. 3 Source selector: CD,TUNER,TAPE/OFF � selects CD, radio or tape source of sound � power off switch 4 BAND � selects waveband 5 TUNING � tunes to radio stations 6 LIFT TO OPEN � opens/ closes the CD door. 7 CASSETTE RECORDER keys: PAUSE� pauses playback or recording STOP�EJECT � stops the tape; � opens the cassette holder. F.FWD/ REW � fast winds/ rewinds tape; PLAY � starts playback; REC � starts recording. 8 PROG � programs tracks and reviews the program 9 .2/; PLAY/PAUSE � starts or pauses CD playback. 0 9 STOP � stops CD playback;; � erases a CD program ! REPEAT � repeats a track/ CD program/entire CD. @ Display � shows the CD functions # STEREO indicator � lights up for stereo FM reception. $ SEARCH �, § � skips or searches a passage/track backwards or forward % POWER indicator � lights up when the set is powered on.

Adjusting volume and sound Adjust the sound with the VOLUME and BASS BOOST controls.

Using AC power WARNING: Always check you have completely switched off the set, before you change or disconnect power supply. 1 Check if the power voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. If your set is equipped with a voltage selector, adjust the selector so that it matches with the local mains. 3 Connect the power cord to the AC ~ inlet and the wall socket.The power cord is now connected and ready for use. To switch the set off completely, withdraw the power cord from the wall socket. Disconnect the power cord from the wall socket to protect your set during heavy thunderstorms. The type plate are located on the bottom of the set. Helpful hints: � 1 2 3

Radio reception
Adjust the Source selector to TUNER. Adjust BAND to select your desired waveband, AM (MW) or FM ST. (stereo) Turn TUNING to tune to a station. - STEREO indicator lights up for stereo FM reception. To improve radio reception: � For FM, extend and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. To tune to a weak FM station, adjust BAND to FM (mono). For AM (MW), the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set.

CAUTION
Use of controls or adjustments or performance of procedures other than herein may result in unsafe operation.

Power Supply
Whenever convenient, use the power supply cord if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries. Batteries (not included) Open the battery compartment and insert 6 batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "+" and "�" symbols inside the compartment. (See 2) 2 Replace the compartment door, making sure the batteries are firmly and correctly in place. The set is now ready to operate. Batteries contain chemical substances, so they should be disposed of properly.

2

4 �

1

� To avoid unnecessary energy consumption, always adjust the Source selector to TAPE/ OFF after using the set. Also check that the tape deck keys are released.