Gruba instrukcja - poprostu wszystko co potrzreba - polecam .
Tekstowy podgląd strony 8 (kliknij aby zobaczyć)
CASSETTE RECORDER
CD Synchro Start Recording 1. Adjust the POWER slider to CD. 2. Insert a CD and if desired, program track numbers. 3. Insert a suitable tape into the cassette deck and close the door. 4. Press RECORD 0 to start recording. � Playing of the CD program starts automatically from the beginning of the program. You don't need to start the CD player separately. To select and record a particular passage within a CD track: � Press SEARCH � or §. Release the control when you recognize the passage you want. � To pause CD playback, press 2;. � Recording starts from this exact point in the track when you press RECORD 0. 5. To pause recording, press PAUSE ;. Press PAUSE ; again to resume recording. 6. To stop recording, press OPEN�STOP 0 9. Recording from the Radio 1. Tune to the desired radio station (see Tuning to radio stations). 2. Follow steps 3-6, under CD Synchro Start Recording.
SAFETY & MAINTENANCE
SAFETY & MAINTENANCE INFORMATION (See 7) � Don't expose the set, batteries, CDs or cassettes to humidity, rain, sand or excessive heat. � Clean the set with a dry cloth. Don't use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. � Place the set on a hard and flat surface so that the system does not tilt. Make sure there is good ventilation to prevent the set overheating. � The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. CD player and CD handling � If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. � The lens of the CD player should never be touched! � Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. � Always close the CD and tape door to avoid dust on the lens. � To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. � Never write on a CD or attach any stickers to it. Tape deck maintenance To ensure quality recording and playback of the tape deck, clean parts A, B and C as shown, once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. 1. Open the tape door. 2. Press PLAY 1 and clean the roller C. 3. Press PAUSE ; and clean the heads A, and the capstan B. 4. After cleaning, press OPEN�STOP 0 9. Note: Cleaning of the heads can also be done by playing a cleaning cassette through once.
TROUBLESHOOTING
If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING: Do not open the set as there is a risk of electric shock! Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee.
No sound /power � � � � � � Volume not adjusted Adjust the VOLUME Mains lead not securely connected Connect the AC mains lead properly Batteries exhausted/ incorrectly inserted Insert (fresh) batteries correctly dAtA indication � CD contains non-audio files � Press SEARCH � or § once or more to skip to a CD audio track, instead of the data file The CD skips tracks � CD damaged or dirty � Replace or clean CD � SHUFFLE or PROG is active � Switch off SHUFFLE / PROG Poor cassette sound quality � Dust and dirt on the heads, etc. � Clean deck parts, see Maintenance � Use of incompatible cassette types (METAL or CHROME) � Only use NORMAL (IEC I) for recording Recording does not work � Cassette tab(s) may be broken � Apply adhesive tape over the missing tab space
Severe radio hum or noise � Electrical interference: set too close to TV, VCR or computer � Move the set to increase the distance Poor radio reception � Weak radio signal � FM: Adjust the FM telescopic aerial nocd indication � CD badly scratched or dirty � Replace/ clean CD, see Maintenance � Laser lens steamed up � Wait until lens has cleared nFcd indication � CD-R(W) is blank/ not finalized � Use a finalized CD-R(W)
Environmental information
We have done our best to reduce the packaging and make it easy to separate into 3 materials: cardboard, expandable polystyrene, polyethylene. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, exhausted batteries and old equipment.
