|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
 ;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
;
...instrukcja serwisowa w pełni czytelna i kompletna. Dziękuję!
SETTING CLOCK RESETTING THE MICROCOMPUTER
EQUALIZER q To erase all of the stored memory contents (clock and timer (Main unit operation) tem. X-BASS/ settings, tuner and CD presets). DEMO q If the display is not correct.
Reset microcomputer under the following conditions: In this example, clock is set for the 12-hour (AM 12:00) sys-
q If the operation is not correct.
MEMORY/SET
POWER Within 5 seconds, press the MEMORY/SET button. ON/
1
Press ON/STAND-BY button to enter the stand-by mode.
2 Press the CLOCK button. 1 Press ON/STAND-BY button to enter the stand-by mode. 3 2
ON/ BASS/DEMO button, hold down the ON/STAND-BY button for STAND-BY at least 1 second. Press TUNING/TIME ( or ) button to select the time
POWER STAND-BY While pressing down button and the EQUALIZER/X-
4
(AM 12:00 PM 11:59) Caution: TIME (AM 0:00 PM 11:59) memory including clock timer settings, tuner and CD
presets. "0:00" � The 24-hour display will appear.
display mode. q "CLEAR AL" will appear.
CLOCK "AM 12:00" � The 12-hour display will appear. TUNING/
"AM 0:00" � 12-hour display appear. q The operation explained above will erase all data stored in ( ) (0:00 23:59)
q Note that this can only be set when the unit is first installed
or it has been reset (see page 15).
2
5 Press the MEMORY/SET button. 6 Press TUNING/TIME ( or ) button to adjust the hour.
q Press the TUNING/TIME ( or ) button once to advance
the time by 1 hour. Hold it down to advance continuously.
q When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
3
4 minutes.
7 Press the MEMORY/SET button. 8 Press TUNING/TIME ( o r ) button to adjust the
OPERATION MANUAL
�5�
q Press the TUNING/TIME ( or ) button once to advance
q The hour setting will not even if minutes advance from
by 1 minute. Hold it down to change the time in 5 minute intervals. 12:00 AM 0:00
"59" to "00".
q The clock starts operating from "0" second.
9 Press the MEMORY/SET button. 5
(Seconds are not displayed.) And then the clock display will disappear after a few seconds.
To see the time display:
Press the CLOCK button.
q The time display will appear for about 5 seconds.
6
Note: q The clock display will flash on and off at push of the CLOCK button when the AC supply is restored after a power
failure occurs or after the AC power cord is disconnected.
7
If this happens, follow procedure below to change the clock time.
To change the clock time:
8 xPress the CLOCK button. yWithin 5 seconds, press the MEMORY/SET button.
9 zPerform steps 6 9 above.
To change the time display mode:
xPerform steps 1 2 in the section "RESETTING THE
MICROCOMPUTER", on page 15.
CD-BA120/125
yPerform steps 1 9 above.
|
|
|
> |
|
