SHARP CDBK190V
Instrukcja Serwisowa

(Continued) SETTING THE CLOCK

5
In this example, clock is set for 24-hour (0:00) sysPress the MEMORY/SET button. Connecting the AC power lead AM/FM interval (span) tem. (Main unit operation)

Check setting of AC voltage selector located on the The International Telecommunication Union (ITU) has rear panel before plugging the unit into an AC socket. If necestablished that member countries should maintain either a essary, adjust selector correspond to the AC power 10 or a 9 kHz interval between broadcasting frequenvoltage used in your area. cies of any AM station. The illustration shows the 9 kHz

zones (regions 1 3), and 10 kHz interval Press the TUNING/TIME ( or ) button to adjust

6

Selector adjustment: zone (region 2). the hour. ON/ Turn selector with a screwdriver until appropriate Before using unit, set SPAN SELECTOR switch (on Press the TUNING/TIME ( or ) button once to STAND-BY voltage number appears in window (110V, 127V, 220V rear panel) AM tuning interval (span) of your area. the time by 1 hour. Hold it down to advance conor 230V 240V AC). tinuously.

CLOCK automatically to "PM". MEMORY/SET

When the 12-hour display is selected, "AM" will change

TUNING/ TIME 7 ( )
Press the MEMORY/SET button.

1

1 Press ON/STAND-BY button to enter the stand8 Press the TUNING/TIME ( or ) button to adjust
by mode. the minutes.

2

Press the TUNING/TIME ( or ) button once to Press the CLOCK button. advance time by 1 minute. Hold it down to change the time in 5-minute intervals. The hour setting will not advance even if minutes advance from "59" to "00".

�7�

3 Within 5 seconds, press the MEMORY/SET button. 9 Press the MEMORY/SET button.
The clock starts operating from "0" second. (Seconds are not displayed.) And then clock display will disappear Press TUNING/TIME ( or ) button to select the

2

To change the tuning zone: time display mode. after a few seconds. To an AC socket

4

1 Press ON/STAND-BY button to enter the stand"0:00" The 24-hour display will appear. (0:00 -

2 Set the SPAN SELECTOR switch to "50/9" for 9 kHz "AM 0:00" The 12-hour display will appear. (AM 0:00

by mode. 23:59)

To see the time display:
Unplug power lead from AC socket if the unit

Notes: AM interval (50 kHz FM interval), and "100/10" for 10 PM 11:59) Plug the power lead into an AC socket, after any connections. Whilst pressing down button and the X-BASS/ DEMO button, hold down the ON/STAND-BY button will not be in use for a prolonged period of time. for at least 1 second.

3

12:00 PM 11:59) The time display will appear for about 5 seconds.

AM interval (100 kHz FM interval). Press the CLOCK button. "AM 12:00" The 12-hour display will appear. (AM

Note that this can only be set when the unit is first Note: "CLEAR AL" appear. The clock display will flash on and off at push of the installed or it has been reset.

CLOCK button when the AC power supply is restored

a failure occurs or after the AC power lead is disconnected. If this happens, follow the procedure below to change the clock time. To change the clock time:

AC Plug Adaptor In areas (or countries) where an AC socket as shown in Caution: illustration is used, connect unit using the AC plug The operation explained above will erase all data stored adaptor supplied with the unit, as illustrated. The AC plug in memory including clock timer settings, and tuner adaptor is not included in areas where the AC wall socket and CD presets. and AC power plug can be directly connected (see illustration ). 1 Press the CLOCK button.

0:00 AM 12:00
2 Within 5 seconds, press the MEMORY/SET button. 3 Perform steps 6 9 above. To change the time display mode: Perform steps 1 2 in "RESETTING THE MICROCOMPUTER". 2 Perform steps 1 9 above.

CD-BK1600V/1800V/190V