|
|
|
Kto jest w sklepie?
Sklep przegląda 6043 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
SETTING CLOCK RESETTING THE MICROCOMPUTER
(Main unit operation) 1,2
In this example, clock is set for q To erase all of the stored memory contents (clock and timer Press the CLOCK button.
Reset microcomputer under the following conditions:
24-hour (0:00) system. settings, tuner and CD presets). Press ON/STAND-BY button to enter the stand-by mode.
1 2
Press ON/STAND-BY button to enter the stand-by mode.
ON/ Press TUNING/TIME ( or ) button to select the time STAND-BY display mode. While pressing down VOLUME button and the oniy
3 Within 5 seconds, press the MEMORY/SET button. 2 1 4
Caution: (AM 12:00 PM 11:59) q The operation explained above will erase all data stored in CLOCK "AM 0:00" � The 12-hour display will appear. memory including clock timer settings, tuner and CD (AM 0:00 PM 11:59) presets.
or it has been reset (see page 23).
q If the display is not correct. q If the operation is not correct.
CD-C421H / C411H
2
TUNING/TIME button, hold down the ON/STAND-BY button
TUNING/
for at least 1 second. SET ( ) "AM 12:00" � The 12-hour display will appear.
"0:00" � The 24-hour display will appear. TIME MEMORY/ (0:00 23:59)
q Note that this can only be set when the unit is first installed
2 5 Press the MEMORY/SET button. 6 Press TUNING/TIME ( or ) button to adjust the hour.
the time by 1 hour. Hold it down to advance continuously. q When the 12-hour display is selected, "AM" will change automatically to "PM".
3 q Press the TUNING/TIME ( or ) button once to advance 7 Press the MEMORY/SET button.
Press TUNING/TIME ( o r ) button to adjust the minutes. q Press the TUNING/TIME ( or ) button once to advance
4
12:00 AM 0:00 8
5
by 1 minute. Hold it down to change the time in 5 minute intervals. q The hour setting will not even if minutes advance from
OPERATION MANUAL
�6�
6 "59" to "00". 9 Press the MEMORY/SET button.
q The clock starts operating from "0" seconds. (Seconds are not displayed.)
7 8
Note: q In event of a failure or when the AC power lead is disconnected, the clock display will go out. When AC power supply is restored, the clock display will flash on and off to indicate time when the power failure occurred or when the AC power lead was disconnected. If this happens, follow procedure below to change the clock time.
9
To change the clock time:
When unit is in the stand-by mode: x Press the MEMORY/SET button. y Perform steps 6 9 above. When the unit is on: x Press the CLOCK button. y Within 5 seconds, press the MEMORY/SET button. z Perform steps 6 9 above.
To see the time display:
Press the CLOCK button. q The time display will appear for about 5 seconds.
To change the time display mode:
x Perform steps 1 2 in the section "RESETTING THE MICROCOMPUTER", on page 23. y Perform steps 1 9 above.
|
|
|
> |
|
