|
|
|
Kto jest w sklepie?
Sklep przegląda 5912 gości i
14 zarejestrowanych klientów |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
SETTING CLOCK RESETTING THE MICROCOMPUTER
ditions: Press ON/STAND-BY button to enter the stand-by mode.
(Main unit operation)
q To erase all of the stored memory contents (clock and timer q If the display is not correct.
In this example, clock is set for the 24-hour (0:00) system. Reset microcomputer under the following con-
1
CD-DP2500H
2 Press the CLOCK button. settings, tuner and CD presets). 3 Within 5 seconds, press the MEMORY/SET button. q If the operation is not correct.
1 Press ON/STAND-BY button to enter the stand-by mode. 4 2 Whilst pressing down / button and the X-BASS display mode.
second. (0:00 23:59)
Press TUNING/TIME ( or ) button to select the time
�0:00� �The 24-hour display will appear. button, hold down the ON/STAND-BY button for at least 1
�AM 0:00� �The 12-hour display will appear. q �CLEAR AL� will appear. (AM 0:00 PM 11:59) Caution: (AM 12:00 PM 11:59) memory including clock timer settings, tuner and
�AM 12:00� �The 12-hour display will appear. q The operation explained above will erase all data stored in stalled or it has been reset.
q Note that this can only be set when the unit is first inCD presets.
5 Press the MEMORY/SET button. 6 Press TUNING/TIME ( or ) button to adjust the hour.
vance the time by 1 hour. Hold it down to advance continuously. automatically to �PM�.
q Press the TUNING/TIME ( or ) button once to ad-
q When the 12-hour display is selected, �AM� will change
7 Press the MEMORY/SET button. 8 Press TUNING/TIME ( or ) button to adjust the min-
OPERATION MANUAL
�8�
(Seconds are not displayed.) And then the clock display will disappear after a few seconds.
utes. q Press the TUNING/TIME ( or ) button once to advance time by 1 minute. Hold it down to change the time in 5 minute intervals. q The hour setting will not even if minutes advance from �59� to �00�.
9 Press the MEMORY/SET button.
q The clock starts operating from �0� second.
To see the time display:
Press the CLOCK button. q The time display will appear for about 5 seconds.
Note: q The clock display will flash on and off at push of the CLOCK button when the AC power supply is restored after a failure occurs or after the AC power lead is disconnected. If this happens, follow procedure below to change the clock time.
To change the clock time:
1 Press the CLOCK button.
2 Within 5 seconds, press the MEMORY/SET button.
3 Perform steps 6 9 above.
To change the time display mode:
Perform steps 1 2 in the section �RESETTING THE MI-
CROCOMPUTER�.
2 Perform steps 1 9 above.
|
|
|
> |
|
