|
Kto jest w sklepie?
Sklep przegląda 5958 gości
|
Kategorie
|
Informacje
|
Polecamy
|
|
|
|
|
Dla tego produktu nie napisano jeszcze recenzji!
;
Dobrej jakości skan - wkońcu mogłem poznać wszystkie funkcje tego odtwarzacza - polecam .
;
Gruba instrukcja - poprostu wszystko co potrzreba - polecam .
Using Your Cooktop
Models CEX375VB (shown) & CEX375VW(white)
surface unit
6� solid element
Left rear
control knob
Right rear
I
is cooktop
control knob
Bum, Fire And Property Damage Hazard n Be sure all control knobs are turned to OFFand all signal lights are off when you are not cooking. Someone could be burned or a fire couJd start if a surface unit is accidentally left on. l Solid elements stay hot for a long time. Do not use the high setting for long periods of time or leave pans on hot elements when cooking is done. Burned food and damage to the cookware could result.
Cookware
element surface unit
7 112�solid
control Imob
Left front �
panel
Control
Signal light
� Right front \ control knob
Model and serial number plate (on bottom of outer box)
Using the surface units
Push in Use a medium-low setting to keep food
cooking after starting it on a higher setting. Use a low setting to keep food warm until ready to serve. Set the heat higher or lower within the low band to keep food at the temperature you want.
Solid element surface units
Control knobs must be pushed in before turning them to a setting. They
can be set anywhere between HI and OFF.
Before using a solid element surface unit for the first tune, heat on high setting for five minutes. The surface unit will give off smoke as the protective coating, applied at the factory, finishes bonding to the surface. Solid cast-iron to provide are cooking. heavyelement surface unitsevenmade of Each surface unit has a built-in protective limiter as a safety feature. The limiter senses uneven cooking temperatures and automatically reduces the heat level. The limiter will sense uneven heat when a pan boils dry or when a pan is removed and the surface unit is left on. The heat level may also be reduced automatically if the bottom of the pan is not flat or if the pan is too large or too small for the element. This will result in longer cooking times. Solid elements hold heat longer than conventional surface units. For best cooking results, use a high setting for only a short period of time. Then use a lower setting to complete the cooking. You may want to turn the solid element surface unit OFF a few minutes before you finish cooking.
Signal lights
The Surface Unit Signal Light next to a control knob will glow when that surface unit is on.
NOTE: When a Signal Light goes off, the
Pans should be the same size or larger than the surface unit to prevent boilovers and hot handles. Use only flat-bottomed utensils. Flat bottoms allow maximum contact between the pans and surface units for fast, even cooking. Pans with uneven bottoms are not suitable. bottoms or with raised patterns on the Do not use
trivets, woks with skirts, or canners with concave or ridged bottoms.
surface unit will still be hot. Do not leave or store plastic, pans or other items on surface units.
Until you get used to the settings, use the following as a guide. For best
To check your cookware for flatness, place a straight-edge across the bottom of each piece. Rotate the straight-edge across the bottom. If light shows anywhere between the pan and the straight-edge, the pan is not flat. Do not
results, start cooking at the high settings, then turn the control knob down to continue cooking. Use a high setting to start food cooking; to bring liquids to a boil. Use a medium-high setting to hold a rapid boil; to fry chicken or pancakes.
Use a medium setting for gravy,
puddings and icing; to cook large amounts of vegetables.
Bum Hazard If the pan is too small for the surface unit, you could be burned by the heat from the exposed section of the surface unit. Use correctly sized utensils to prevent injury.
Page 3
|
|
|
> |
|