|
|
|
Kto jest w sklepie?
Sklep przegląda 5958 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
�. Re-Adjustment
Ａ���� changing the Signal Board or Panel Module, re-adjustment is needed according to the item 7.1 to 7.5 . For Video Board, item 7.3 to 7.5 are needed. 7.1 Personal Computer (PC) input black level/fundamental amplitude adjustment How to prepare 1.Connect RGB input terminal VGA (75), 0.7Vpeak, no-set up, horizontal 16 stairs bar signal. Initial adjustment data must be 8 bit resolution. 2.Appear and adjust screen OSD Menu of Picture: Contrast:: Max, Brightness: 0, and options are Color select: NORM, GAMMA: 1.0, Video level: 0.7V Set adjustment No. 246, 247 and 248 scale to 16 . Adjustment No240 is GAMMA function.( 0=GAMMA1.0, 1=GAMMA2.2) How to adjust 1.Set factory preset mode and adjust as follows by Remote Control Transmitter. 2.Set adjustment No.41 to just darken black level.(GAMMA1.0) 3.Set adjustment No.42 to just darken black level.(GAMMA1.0) 4.Set adjustment No.43 to just darken black level.(GAMMA1.0) 5.Connect Full black signal and check that no residual color area is observed. If residual color area is observed, re-adjust No.41, 42 and 43 to disappear it. 6.At adjustment No.44, adjust that 2nd step of White peak is just distinguished.(GAMMA=2.2) 7.At adjustment No.45, adjust that 2nd step of White peak is just distinguished.(GAMMA2.2) 8.At adjustment No.46, adjust that 2nd step of White peak is just distinguished.(GAMMA2.2) 9.Change to No47. 10. Check that setup level is darken and also 2nd step of white level is distinguished. 11.Check that 2nd step of white peak is distinguishable. Tolerance of each color adjustment numbers are less than 7. If more than 7. re-adjust from above 2. step. 7.2 PC color temperature adjustment How to prepare 1. Set factory preset mode. 2. Connect window pattern signal (25% of display area) VGA (75), 0.7Vp-p without set up signal . 3. Window pattern (R, G and B) should be 8 bit resolution each. 4. Appear and adjust Screen OSD menu of Picture. Contrast: Max, Brightness: 0, and options are Color select: NORM, GAMMA: 2.2, Video level: 0.7V Set adjustment No. 246, 247 and 248 scale to 16 . Video input level should be 0.7Vp-p. How to adjust 1.Set factory preset mode and adjust as follows by Remote Control Transmitter. 2.Measurement probe of CRT Color Analyzer CA-100 is set on the center of screen. (Center of white peak signal.) 3.Adjust color temperature as follows by reducing one or two numbers of No.32, 33, 34.
10
|
|
|
> |
|
