|
|
|
Kto jest w sklepie?
Sklep przegląda 5714 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
SETTING THE CLOCK PREPARATION FOR USE
1 Press ON/STAND-BY switch to enter the stand-by mode.
Press CLOCK button. Replace the batteries if control distance decreases or oper(0:00) system. Within 3 seconds, press the MEMORY/SET button. Notes concerning use: In this example, clock is set for the 24-hour
2 3
Exposing sensor on the main unit to strong light may in"0:00" � The 24-hour display will appear. terfere with operation. Change lighting or the direction of 0.2 6 m (8" 20') "AM 0:00" � The 12-hour display will appear. Keep the remote control away from moisture, excessive heat,
1 5
ON/ display. STAND-BY
4 Press TUNING/TIME ( or ) button to select time and sensor on the main unit with a soft cloth.
ation becomes erratic. Periodically clean transmitter LED on the remote control
CLOCK (0:00 23:59) the unit.
CD-C410H,CP-C410
MEMORY/ (AM 0:00 PM 11:59) shock, and vibrations. SET "AM 12:00" � The 12-hour display will appear. 1
(AM 12:00 PM 11:59) Press the MEMORY/SET button. ( )
TUNING/TIME
5 6 Press TUNING/TIME ( or ) button to adjust the hour. 2 7 Press the MEMORY/SET button.
Press ON/STAND-BY (POWER) switch to enter the standtions:Reset microcomputer under the following condiPress TUNING/TIME ( o r ) button to adjust the minutes. Press TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continuously. When the 12-hour display is selected, "AM" will change automatically to "PM".
RESETTING THE MICROCOMPUTER
3 8 1 4
0:00 AM 12:00
by mode.
2
The clock starts operating from "0" seconds. (Seconds are not displayed.) Note: is disconnected, the clock display will go out. When AC power supply is restored, the clock display will flash on and off to indicate time when the power failure If this happens follow procedure below to change the clock time.
Press button for at least 0.5 seconds to change time To erase all of the stored memory contents (clock in 5 minute intervals. timer settings, tuner and CD presets). Press and hold down VOLUME button, the The hour setting will even if minutes advance If display is not correct. button and ON/STAND-BY (POWER) switch all at the from "59" to "00". same time. Hold them for at least 1 second. If the operation is not correct.
5 9 Press the MEMORY/SET button.
OPERATION MANUAL
�6�
To change the clock time: 8
6 In event of a failure or when the AC power lead
7 occurred or when the AC power lead was disconnected.
1 Press the MEMORY/SET button. 2 Perform steps 6 9 above. 9 1 Press the CLOCK button. 2 Within 3 seconds, press the MEMORY/SET button. 3 Perform steps 6 9 above.
To see time display: (When the power is ON)
Press the CLOCK button. The time display will appear for about 3 seconds. When the ON/STAND-BY switch is set to ON.
When the ON/STAND-BY switch is set to STAND-BY.
To switch the time display mode:
1 Press ON/STAND-BY switch to enter the stand-by mode. 2 Press and hold down VOLUME button, the
button and ON/STAND-BY switch all at the same time. Hold them for at least 2 second. (Refer to RESETTING THE MICROCOMPUTER on page 16.)
3 Perform steps 1 9 above.
Note: The operation explained above will erase all data stored in memory, such as clock timer settings, tuner and CD presets.
|
|
|
> |
|
