|
|
|
Kto jest w sklepie?
Sklep przegląda 5786 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
PREPARATION FOR USE
Notes concerning use:
SETTING THE CLOCK
In this example, clock is set for the 24-hour (0:00) system. ation becomes erratic.
and sensor on the main unit with a soft cloth. Exposing sensor on the main unit to strong light may (8" 20') interfere with operation. Change lighting or the direction
1 Set ON/STAND-BY switch to STAND-BY. Replace the batteries if control distance decreases or oper-
2 Press the CLOCK button. Periodically clean transmitter LED on the remote control
STAND-BY
of the unit. CLOCK
1 Keep the remote control"AM away12:00" from� moisture,The excessive12-hour heat,display 1will 5appear.
3 4
ON/ Within 5 seconds, press the MEMORY/SET button. 0.2 6 m
Press TUNING/TIME ( or ) button to select the time
display mode.
MEMORY/ shock, and vibrations. (AM 12:00 PM 11:59) SET "AM 0:00" � The 12-hour display will appear.
(AM 0:00 PM 11:59)
TUNING/TIME "0:00" � The 24-hour display will appear. ( ) (0:00 23:59)
5 Press the MEMORY/SET button.
2 6 Press TUNING/TIME ( or ) button to adjust the hour. RESETTING THE MICROCOMPUTER
3 ously. To erase all of the stored memory contents (clock and timer
If the display is not correct.
Press TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continuReset microcomputer under the following conditions:
When the 12-hour display is selected, "AM" will change autosettings, tuner and CD presets). matically to "PM".
4 7 Press MEMORY/SET button. If the operation is not correct. 2 8
Note: Press TUNING/TIME ( o r ) button to adjust the
1,2 2 contents of preset memory" on page 19. 1 Press ON/STAND-BY switch to enter the stand-by mode. The hour setting will not even if minutes advance 2 Press VOLUME button, the TUNING/TIME button
12:00 AM 0:00
minutes. To tuner preset memory, see "To erase all of the
5 in 5-minute intervals.
Press button for at least 0.5 seconds to change the time
from "59" to "00".
CD-C470H,C470E,C480H/CP-C470H,C470E,C480H
OPERATION MANUAL
�6�
9 Press the MEMORY/SET button. and ON/STAND-BY switch all at the same time. Hold 6
The clock starts operating from "0" seconds. (Seconds are them down for at least 1 second. not displayed.)
7 Note:
8 flash on and off to indicate time when the power failure
In event of a failure or when the AC power lead is disconnected, the clock display will go out. When AC power supply is restored, the clock display will
occurred or when the AC power lead was disconnected. If this happens, follow procedure below to change the clock time.
9
change clock time: To see time display: (When the power is ON)
When the ON/STAND-BY switch is set to STAND-BY. Press the CLOCK button.
The time display will appear for about 5 seconds. When unit is in the demonstration mode, press
DEMO button to enter the clock mode.
To switch the time display mode:
Press the MEMORY/SET button.
1 2 1 Set the ON/STAND-BY switch to STAND-BY. Perform steps 6 9 above.
2 Press VOLUME button, the TUNING/TIME button
2
When the ON/STAND-BY switch is set to ON. and ON/STAND-BY switch all at the same time. Hold them Press the CLOCK button. down for at least 1 second. Within 5 seconds, press the MEMORY/SET button. Perform steps 6 9 above.
1
Note: The operation explained above will erase all data stored in memory, such as clock timer settings, tuner and CD presets.
3 Perform steps 1 9 above. 3
|
|
|
> |
|
