JVC CS-SR100J
Instrukcja Obsługi

Connection Diagram

REAR VIEW
Right Speaker Home Docking Cradle for JVC Sirius tuner Audio Output (Green connector)

REAR VIEW
Left Speaker

Green plug (stereo mini: � 3.5 mm)

Brown connector Line input cord Brown plug (mini: � 2.5 mm) Left speaker cord Black plug AC adapter (AC 120 V , 60 Hz)

Using the Speaker System

To an AC outlet After completing all other connections, plug in the AC adapter.

1 2 3

Connect the speakers and AC adapter as shown in the Connection Diagram. Turn the power switch knob clockwise to turn the power on. A click sound is heard and the power lamp lights up in green. Turn the power switch knob further to obtain the optimum sound level. � In case the sound level is not sufficient though the knob is turned up fully clockwise, increase the output level of the signal source as it may be set too low. � When using the headphones, plug it into the headphone jack. No sound comes out of the speakers. Turn the knob fully counterclockwise before connecting the headphones, not to damage the speakers and your ears.

Maintenance
If cleaning is required, disconnect the AC adapter from AC outlet, and wipe off with soft cloth. For removing heavy stain, use the cloth moistened with neutral detergent. Do not use inflammable or harmful fluid such as benzine or thinner.

To turn off the speakers, turn the power switch knob fully counterclockwise. � Never turn it on or off by any other means to ensure safe operation of the speakers.

Parts Identification
7 Front
Left speaker Right speaker

Troubleshooting
Check the following if you think the system is not working correctly. � If the problem should persist, unplug the AC adapter from the AC outlet, and refer servicing to the qualified service personnel. Symptom
Power lamp is turned off. Power lamp is turned on, but no sound. Power lamp Sound is distorted.

Possible Cause
� AC adapter is not connected. � No power is supplied. � Line-input cord is not connected. � Volume level is too low. � Volume level is too high. � Input sound level is too high.

Remedy
� Plug in adapter firmly. � Try another AC outlet. � Plug in the cord firmly. � Turn up the volume control. � Turn down the volume control. � Adjust it to the optimum level. � Adjust it to the optimum level.

Sound level is too low. � Input sound level is too low. Sound comes out of only one speaker.

Headphone jack

� Line-input cord is not connected firmly. � Plug in the cord firmly. � Left speaker is not connected to the � Plug in Speaker cord firmly. right speaker.

Power switch (volume control) knob

Although the speakers are magnetically shielded, they may affect some monitors if installed nearby. Should color deterioration occur on a monitor, place the speakers slightly away. Turn off the monitor, and keep it turned off for about 15 to 20 minutes. By doing this, normal color will be restored.
Left speaker

7 Rear
Right speaker

Specifications
7 Amplifier: Power output Input impedance Input sensitivity Power supply Power consumption Signal-to-noise ratio 1.5 W per channel (at 10 % THD) 12 k� (nominal) 200 mV/1 kHz/1 W DC 9 V 500 mA (by AC adapter) 12 W 72 dB AC 120 V , 60 Hz Plastic molded 100 Hz � 20 000Hz 90 mm x 50 mm (3-9/16 in. x 2 in.) cone type, magnetically shielded
Left speaker cord (brown plug): 2 m (6.5 ft)

DC IN jack

Line-input cord (green plug): 2 m (6.5 ft)

L SPKR (left speaker) jack (brown connector)

7 Power Requirements: 7 Speaker System: Enclosures Frequency response Speaker uint 7 Dimensions (H/W/D): Right speaker: Left speaker: 7 Mass:

200 mm x 80.5 mm x 112 mm (7-7/8 in. x 3-1/4 in. x 4-7/16 in.) 200 mm x 80.5 mm x 99.3 mm (7-7/8 in. x 3-1/4 in. x 3-15/16 in.) Left speaker: 345 g (0.77 lbs)

Right speaker: 400 g (0.89 lbs)

* Design and specifications are subject to change without notice.