AIWA CX-JTD8
Instrukcja Serwisowa

CX-JTD8

[5]: SACD Hybrid disc (CD layer, normal speed, 8 cm) [6]: SACD Hybrid disc (CD layer, double speed, 8 cm)
2-2. Servo Control
Note: Be sure to perform the disc type setup before performing this item.

[8] 20kTj REV : 20k track jump (direct search) reverse. [10/0] : All servo off.
2-4. Non EEPROM Write Adjust Non EEPROM Write Adjust

Servo Control 1.LD off R.Sled 2.Focus off L.Sled 3.SPDL off U.Sled 4.CLVA off D.Sled 5.Trk. off 6.Sled off 7.Fcs.Srch off

FWD REV Reset Limit

1. 2. 3. 4. 5. 6.

Focus Focus Trk. Trk. Trk. EQ

Offset Gain Offset Coarse Offset Fine Gain Boost

0.All Servo Off 0.All Servo Off Exit: RETURN Exit: RETURN On this screen, the servo on/off control necessary for replay is executed. Normally, turn on each servo from 1 sequentially and when CLVA is turned on, the usual trace mode becomes active. In the trace mode, DVD sector address or CD time code is displayed. This is not displayed where the spindle is not locked. The spindle could run overriding the control if the spindle system is faulty or RF is not present. In such a case, do not operate CLVA. On this screen, each item can be adjusted automatically. Select the desired number [1] to [10/0] from the remote commander, and current setting for the selected item will be displayed, then increase or decrease numeric value with the O key or o key. If CLV has been applied, the jitter is displayed for reference for the adjustment.

[1] Focus Offset : Adjusts focus offset. [2] Focus Gain : Adjusts focus gain. [3] TRK. Offset Coarse : Adjusts tracking offset of the RF [4] TRK. Offset Fine [5] TRK. Gain [6] EQ Boost [10/0]
amp (IC001) side. : Adjusts tracking offset of the DSP (IC401) side. : Adjusts track gain. : Adjusts amount of boost of equalizer. : All servo off.

[1] LD : Turn on/off the laser. [2] Focus : Search the focus and turn on the focus. [3] SPDL : Turn on/off the spindle. [4] CLVA : Turn on/off normal servo of spindle servo. [5] Trk. : Turn on/off the tracking servo. [6] Sled : Turn on/off the sled servo. [7] FCS. Srch : Turn on/off the focus search. [10/0] : All servo off. [R] Sled FWD (right cursor) : Move the sled forward. [L] Sled REV (left cursor) : Move the sled reverse. [U] Sled FWD (up cursor) : Reset the sled. [D] Sled REV (down cursor) : Limit in the sled.
2-3. Track/Layer Jump Track/Layer Jump FWD REV Fine FWD Fine REV Dirc FWD Dirc REV Dirc FWD Dirc REV

2-5. EEPROM Write Adjust EEPROM Write Adjust 1. 2. 3. 4. 5. 6. Focus Focus Trk. ������ Trk. EQ Offset Gain Offset Coarse Gain Boost

1. 1Tj 2. 1Tj 3.500Tj 4.500Tj 5.10kTj 6.10kTj 7.20kTj 8.20kTj

0.All Servo Off

Exit: RETURN On this screen, each item can be adjusted automatically. Select the desired number [1] to [10/0] from the remote commander, and selected item is adjusted automatically. Thus value is stored in the EEPROM.

0. All Servo Off Exit: RETURN On this screen, track jump, etc. can be performed. Only for the DVD dual layer disc, the focus jump and layer jump are displayed in the right field

[1] Focus Offset : Adjusts focus offset. [2] Focus Gain : Adjusts focus gain. [3] TRK. Offset Coarse : Adjusts tracking offset of the RF [5] TRK. Gain [6] EQ Boost [10/0]
amp (IC001) side. : Adjusts track gain. : Adjusts amount of boost of equalizer. : All servo off.

[1] [2] [3] [4] [5] [6] [7]

1Tj FWD 1Tj REV 500Tj FWD 500Tj REV 10kTj FWD 10kTj REV 20kTj FWD

: 1 track jump forward. : 1 track jump reverse. : 500 track jump (fine search)forward. : 500 track jump (fine search) reverse. : 10k track jump (direct search) forward. : 10k track jump (direct search) reverse. : 20k track jump (direct search) forward.

26