|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
 ;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
CX-LEM220 SECTION 5 MECHANICAL ADJUSTMENTS
TAPE MECHANISM DECK SECTION
Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement
Mode FWD Torque meter CQ-102C Meter reading 2.94 mN � m to 7.84 mN � m 31 to 71 g � cm (0.43 � 0.98 oz � inch) 0.14 mN � m to 0.59 mN � m 2 to 6 g � cm (0.02 � 0.08 oz � inch) 6.86 mN � m to 17.64 mN � m 71 to 143 g � cm (0.98 � 1.99 oz � inch) more than 0.98 N � m 100 g or more (3.53 oz or more)
SECTION 6 ELECTRICAL ADJUSTMENTS
DECK SECTION 0 dB = 0.775 V
Precaution 1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjust. 4. The adjustments should be performed with the rated power supply voltage unless otherwise noted. 5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) 6. The adjustments should be performed for both L-CH and RCH. 7. Switches and controls should be set as follows unless otherwise specified. Test Tape
Tape P-4-A100 WS-48B Signal 10 kHz, �10 dB 3 kHz, 0 dB Used for Azimuth Adjustment Tape Speed Check
FWD back tension
CQ-102C
FF/REW
CQ-201B
FWD tension
CQ-403A
Record/Playback Head Azimuth Adjustment Procedure: 1. Mode: Playback
test tape P-4-A100 (10 kHz, � 10 dB) MAIN board SPEAKER terminal (J302) L-CH, R-CH
level meter
set + �
2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.
L-CH peak Output level
within 1dB within 1dB
Screw position
R-CH peak L-CH peak R-CH peak
Screw position
12
|
|
|
> |
|
