|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
 ;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
ENGLISH
PRECAUTIONS
The apparatus shall not be exposed to dripping or splashing. Do not use where there are extremes of temperature (below 5°C or exceeding 35°C) or where direct sunlight may strike it. Because of the CD player�s extremely low noise and wide dynamic range, there might be a tendency to set the volume on the amplifier unnecessarily high. Doing so may produce an excessively large output from the amplifier which could damage your speakers. Sudden changes in the ambient temperature may cause condensation to form on the optical lens inside the unit. If this happens, take out the disc, leave the unit for about 1 hour, and then proceed to operate. The system�s speakers use powerful magnets. Do not place timepieces, credit cards, cassette tapes or video tapes, etc. near the speakers. Do not install this equipment in a confined space, such as a book case or built in cabinet.
CONTROLS (Fig. 5)
General (Fig. 5a)
1. Power button (Y OFF, Z ON) 2. Display 3. Remote sensor (IR) 4. Function button (FUNCTION) 5. Bass expander button (BASS) 6. Sound preset button (SOUND PRESET) 7. Surround button (SURROUND) 8. Headphones socket (PHONES) 9. Volume control (VOLUME)
CD player/ Tuner (Fig. 5b)
1. Repeat play button (REPEAT) 2. Play/Pause button (CD) 3. CD Compartment lid 4. Stop/Clear button (N) 5. Tuner function/Band select button (TUNER/BAND) 6. Tuning buttons (TUNING -, +) 7. Skip/Search/Preset tuning buttons (PRESET -, +/ F, E) 8. FM mode button (FM MODE)
-
CONNECTIONS (Fig. 1)
Note: - Do not connect the mains lead to an AC outlet until all connections have been made. - The system is not completely disconnected from the mains when the power button is set to the Y OFF position.
Cassette deck (Fig. 5c)
1. Play button (TAPE) 2. Stop button (N) 3. Cassette holder 4. Fast forward/ Rewind buttons (PRESET -, +/ F, E) 5. Record/ Record pause button (j)
Speakers
Connect the connector of the left speaker lead to the �L� SPEAKERS socket and the connector of the right speaker lead to the �R� socket. If you have difficulty inserting the speaker lead connector, turn it over and reinsert it.
FM aerial
Extend the aerial wire as straight as possible and, while listening to the sound from the system, secure it in a position which yields minimal distortion and noise.
REMOTE CONTROLS
Controls (Fig. 5d)
1. Number buttons (1-9, 0) 2. Cassette deck controls r: Record muting button m: Record/Record pause button d, c: Fast forward/Rewind buttons a: play button n: Stop button 3. FM mode button (FM MODE) 4. CD player controls i: Play/Pause button n: Stop button REPEAT: Repeat button 5. Memory button (MEMORY) 6. Sound preset button (SOUND PRESET) 7. Tuning buttons (TUNING +, -, f, e) (These buttons can also be used as CD playing tracks skip and search button) 8. Tuner function/Band select button (TUNER/BAND) 9. Volume buttons (VOLUME +, -) 10. Preset tuning button (PRESET) 11. Line function button (LINE) Number buttons (1-9, 0) These buttons are used to select the track numbers on a disc or preset radio stations. If the function is �CD�, the buttons select the track numbers on a disc. If the function is �TUNER�, the buttons select preset radio stations. With any other function, the buttons will not function. - Two buttons must always be pressed. Example: To select No. 3, press 0, then 3. To select No. 10, press 1, then 0. To select No. 25, press 2, then 5.
AM Loop aerial
Assemble the loop aerial as shown in Fig. 3a. Unwind the aerial wires, then connect them to the AM LOOP terminals. Place the loop aerial in a position which yields the best AM reception, or attach it to a wall or other surface as shown in Fig. 3b. Note: To minimize noise, the speaker, mains and any other leads should not come close to the indoor or external aerial lead and AM loop aerial. Do not place the aerial leads close to the system.
Video/Auxiliary equipment
Connect audio leads (not supplied) from the audio output sockets of a video/auxiliary equipment to the LINE IN sockets.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for monitoring or for private listening. The speakers are automatically disconnected when headphones are connected.
4
|
|
|
> |
|
