SONY DCR-TRV10
Instrukcja Serwisowa

Repaired by:

Ver 1.5 2001. 11

4.

SELF-DIAGNOSIS CODE TABLE
Self-diagnosis Code Block Detailed Function Code Symptom/State Correction

C C C C C C C C C C C C C C C C C C C C C C C

2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3

1 2 3 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2

0 0 0 1 1 2 2 2 2 2 3 4 4 1 1 2 2 2 2 2 3 4 4

0 0 0 0 1 0 1 2 3 4 0 0 2 0 1 0 1 2 3 4 0 0 2

Condensation. Video head is dirty. Non-standard battery is used. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time

Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Use the info LITHIUM battery. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning.

T reel side tape slacking when unloading. Load the tape again, and perform operations from the beginning. Winding S reel fault when counting the rest of tape. Load the tape again, and perform operations from the beginning. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning.

Winding S reel fault when counting the Remove the battery or power cable, connect, and perform rest of tape. operations from the beginning. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum FG fault during normal drum operations Difficult to adjust focus (Cannot initialize focus.) Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Inspect the lens block focus reset sensor (Pin !� of CN001 of FP83 flexible board) when focusing is performed when the control dial is rotated in the focus manual mode, and the focus motor drive circuit (IC302 of VC-217 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin 9 of CN001 of FP83 flexible board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC302 of VC-217 board) when zooming is not performed.

E

6

1

0

0

E

6

1

1

0

Zoom operations fault (Cannot initialize zoom lens.)

E

6

2

0

0

Steadyshot function does not work well. (With pitch angular velocity sensor output Inspect pitch angular velocity sensor (SE451 of JK-170 board) stopped.) peripheral circuits. Steadyshot function does not work well. (With yaw angular velocity sensor output Inspect yaw angular velocity sensor (SE450 of JK-170 board) stopped.) peripheral circuits.

E

6

2

0

1

�8�