PIONEER DJM-800/WAXJ5
Instrukcja Obsługi

EFFECT FUNCTIONS (PRODUCING BEAT EFFECTS)

PRODUCING BEAT EFFECTS
Display example
EFFECT SELECT

Effect Name: DELAY 4 BEAT 2, 3 1 AUTO/TAP TAP 2 3 TIME LEVEL/DEPTH 5 ON/OFF
AUTO TAP

CH SELECT

1
MIC

2 A

3 B

4
MST

Effect Channel Select: CH 1

PARAMETER

MIDI BPM %

BPM value: 120 BPM Parameter 1: 500 ms Beat multiple: 1/1

Beat effects allow the instant setting of effect times in synch with the BPM (beats per minute), thus allowing the production of a wide variety of effects in synch with the current rhythm, even during live performances.

3. Set the effect channel selector to the channel you wish to apply the effect to.
¶ The display�s channel name indicator will show the selected channel with red frame. ¶ If [MIC] is selected, the effect will be applied to both microphone 1 and microphone 2.

1. Press the AUTO/TAP button to set the Beats Per Minute (BPM = track speed) measuring mode.
AUTO:The BPM of the input music signal is detected automatically. TAP: The BPM is input manually by tapping on the TAP button. ¶ Whenever power is first turned ON, the function defaults to the [AUTO] mode. ¶ The indicator for the selected mode [AUTO/TAP] lights in the display. ¶ In the event the track�s BPM cannot be detected automatically, the display�s BPM counter will flash. ¶ The effective range in the AUTO mode is 70 to 180 BPM. It may not be possible to measure some tracks accurately. In this case, use the TAP mode for manual BPM input.

4. Press the BEAT button (2, 3) to select the beat multiple to which the effect is to be synchronized.
¶ When 3 is pressed, the beat count calculated from the BPM is doubled, and when 2 is pressed, the beat count calculated from the BPM is halved (some effects also allow �3/4� setting). ¶ The multiple of the selected beat (parameter 1 position) is displayed in seven sections on the display (see P. 32). ¶ The effect time corresponding to the beat�s multiple is set automatically. Example: When BPM = 120 1/1 = 500 ms 1/2 = 250 ms 2/1 = 1 000 ms

[Using the TAP Button for Manual BPM Input]
If the TAP button is tapped two times or more in synch with beat (1/4 notes), the BPM will be recorded as the average value recorded during that interval.
¶ When BPM mode is set to [AUTO], tapping the TAP button will cause the BPM mode to change to the TAP mode, and the interval at which the TAP button is pressed will be measured. ¶ When the BPM is set via the TAP button, the beat multiple becomes �1/1� (or �4/1�, depending on the effect selected), and the time for 1 beat (1/4 notes) or 4 beats will be set as the effect time. ¶ If the TIME dial is rotated while depressing the TAP button, direct BPM can be set manually. If the TIME dial is rotated while holding the TAP button and AUTO/TAP buttons depressed, the BPM can be set in 0.1 units.

5. Set the ON/OFF button to ON to enable the effect.
¶ Each time the button is pressed, the effect alternates ON/OFF (whenever power is first turned ON, the function defaults to OFF). ¶ The ON/OFF button flashes when the effect is ON.

Parameter 1
Rotating the TIME (PARAMETER 1) dial adjusts the temporal parameter (time) for the selected effect. See P. 39 for details regarding the effect on parameter 1 of rotating the TIME (PARAMETER 1) dial.

Parameter 2
Rotating the LEVEL/DEPTH (PARAMETER 2) dial adjusts the quantitative parameter for the selected effect. See P. 39 for details regarding the effect on parameter 2 of rotating the LEVEL/DEPTH (PARAMETER 2) dial.

2. Set the effect selector to the desired effect.
¶ The display will show the name of the selected effect. ¶ See P. 35 to 36 for details regarding the various effects.

37
<DRB1461> En

English