JVC DLAM4000LU
Instrukcja Obsługi

Controls and Features (Cont.)

Controls and Features (cont.)

Remote Control Unit
r e w
ME NU /
E N
LENS

MENU / ENTER (Menu Operation) Button
1
QUICK ALIGN. AV HIDE OPERATE

The remote control supplied with this projector has only one button to navigate through the menus. Pressing the menu operation button too strongly may cause an incorrect operation. So, before you use the button in an actual situation, have some practice to make yourself familiar with using the button.

q

1

2
QUICK ALIGN. OPERATE AV HIDE PRESET PAGE BACK

1

PRESET

PAGE BACK

When using the MENU/ENTER button as a menu operation button : Press the button down straight when displaying the main menu. While the main menu is displayed, if the selected item has a details setting (submenu), pressing the button will cause the submenu to be displayed.

3
LOCK UNLOCK

2
MEN U/E

2 2

TE

4 p 9
AV
RGB/COMPUTER
LENS

R

AV

RGB/COMPUTER

2 2

When using the MENU/ENTER button as a cursor moving button: Press the button toward one of the 5/�/2/3 marks. While the main menu is displayed, use the button to select an item to adjust or make adjustment.

5 6

U
SHIFT

T
ZOOM

+
FOCUS

U
SHIFT

T
ZOOM

+
FOCUS

D

W
LENS

�

D

W
LENS

�
T E R

+
VOLUME

8

�

t

Installing Batteries
Install batteries in the remote control. If the remote control has started to work erratically, replace the batteries.

1 Open the back cover.
Open the back cover in the direction of the arrow.
LOCK UNLOCK

Precautions for using batteries
If batteries are used incorrectly, they may crack or leak liquid. This could cause a fire, burn, malfunction, or staining or damaging the surrounding. Beware of the following: � Do not mix new and old batteries. � Do not mix different types of batteries as they differ in characteristics. � Place batteries so they match the polarities indicated: (+) to (+) and (�) to (�). � Be sure to put the minus (�) end in first to avoid shortcircuiting. � Use only designated batteries. � Remove the batteries if not used for a prolonged period of time. � When the batteries are exhausted, replace them immediately. Otherwise, liquid could leak, or malfunction could occur due to leaked liquids. If the leaked liquid contacts the skin, wipe it off with a cloth, otherwise the skin could become rough. � Do not put batteries into fire or try to recharge them. � Batteries run for six months to one year in normal use. But the batteries supplied are for confirming operation and may not run that long. When the remote control starts failing to work properly, replace the batteries with new ones.

7

No.51666

N

p AV button
Use this button to select the devices such as a video connected to the projector�s AV IN (EXT. input) terminal. Each time you press the button, the selection changes as follows:
Y/C

e QUICK ALIGN. (Quick Alignment) button
Use this button to automatically adjust TRACKING, PHASE, H. POS. and V. POS. of the projected video. During the automatic adjustment, QUICK ALIGNMENT appears on the screen, and disappears after it is finished. Memo
Quick alignment function: Does not work for video input (EXT. IN input terminal) signals. Works only for computer-related (RGB-1 and-2 input terminals) signals.

*

VIDEO

*

2 Install the batteries.
Place the two batteries (AA/R6-size) supplied in the remote control as illustrated below.
ª · ª

YPBPR

* Y/C and VIDEO can be used only when a video board separately sold has been installed.

q LENS LOCK � UNLOCK switch
With this switch set at the LOCK position, adjustment operations (focus, zoom or shift) with the remote control are disabled, preventing adjustment contents from being inadvertently changed while the remote control is being used. When adjustment is needed, set the switch to the UNLOCK position.

CAUTION
� Automatic adjustment with the quick alignment function should be done on a bright still-picture screen. This function may not work correctly on a dark screen or motion-picture screen. If adjustment with this function is not satisfactory, adjust TRACKING, PHASE, H. POS. and V. POS. manually (see pages 30, 36 and 37).

·

r AV HIDE button
Use this button to turn off the video image temporarily. Pressing it again makes the video image to resume.

w PRESET button

3 Close the back cover.
First fit the claw on the back cover into the case, then close the back cover in the direction of the arrow.

While making adjustment on the main or setting menu, use this button to reset the setting of the selected item to the factory-set value. This button works only for numerical settings and does not work for switching ON to OFF.

t Not used with this projector

DLA-M4000LU DLA-M4000LE

12

13