|
|
|
Kto jest w sklepie?
Sklep przegląda 6043 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
Service manual CP 385 / CP785
5-6 Sound amplification The TDA8944J (TDA8946J) is a stereo BTL audio amplifier capable of delivering 2 x 7 W (2 x 15 W) output power to an 8 � load at THD = 10%, using a 12 V power supply and an external heatsink. The voltage gain is fixed at 32dB. With the three-level MODE input the device can be switched from �standby� to �mute� and to �operating� mode. The TDA 8944J outputs are protected by an internal thermal shutdown protection mechanism and short-circuit protection. Power amplifier The power amplifier is a Bridge Tied Load (BTL) amplifier with an all-NPN output stage, capable of delivering a peak output current of 1.5 A. The BTL principle offers the following advantages : - Lower peak value of the supply current. - The ripple frequency on the supply voltage is twice the signal frequency. - No DC-blocking capacitor - Good low frequency performance Mode selection The TDA894xJ has several functional modes, which can be selected by applying the proper DC voltage to pin MODE. Mute : In this mode the amplifier is DC biased but not operational (no audio output). This allows the input coupling capacitors to be charged to avoid pop-noise. The devices is in mute mode when 2.5 V < VMODE < (Vcc-1.5 V). Operating : In this mode the amplifier is operating normally. The operating mode is activated at VMODE < 0.5 V. 5-7 Vertical deflection The vertical driver circuit is a bridge configuration. The deflection coil is connected between the output amplifiers, which are driven in phase opposition. The differential input circuit is voltage driven. The input circuit is especially intended for direct connection to driver circuits which deliver symmetrical current signals, but is also suitable for asymmetrical currents. The output current of these devices is converted to voltages at the input pins via resistors R350 and R351. The differential input voltage is compared with the output current through the deflection coils measured as voltage across R302, which provides internal feedback information. The voltage across R302 is proportional to the output current. Flyback voltage The flyback voltage is determined by an additional supply voltage Vflb. The principle of operation with two supply voltages (class G) makes it possible to fix the supply voltage Vp optimum for the scan voltage and the second supply voltage Vflb optimum for the flyback voltage. Using this method, very high efficiency is achieved. The supply voltage Vflb is almost totally available as flyback voltage across the coil, this being possible due to the absence of a coupling capacitor. Protection The output circuit has protection circuits for : - Too high die temperature - overvoltage of output stage A Guard circuit The guard signal is not used by the TDA936x to blank the screen in case of fault condition. Damping resistor
- 43 -
|
|
|
> |
|
