|
|
|
Kto jest w sklepie?
Sklep przegląda 5969 gości |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
ALIGNMENT INSTRUCTIONS
3.The adjustment of SCREEN 3-1. Confirm the presetting IBRM data of EEPROM according to CRT. 3-2. Press the [S2] KEY of SVC Remocon, horizontal line will be displayed. 3-3. Adjust SCREEN V/R of FBT so that the horizontal line reach the cut-off point. 3-4 To be completed adjustment of screen. Press the [S2] key to escape screen adjustment mode. 4.The adjustment of FOCUS 4-1. Receive PAL RETMA PATTERN(signal of company:2CH., PAL-B). 4-2. Adjust the picture to best distinct picture of 350 Line by revolve Focus Volume. 5.The adjustment of WHITE BALANCE 5-1. NITSUKI Setting : Set Nitsuki to the Auto Mode , Reference to the B , and System to the PAL . 5-2. Setting the Normal Stats 5-2-1. Adjust Picture to Normal mode. 5-2-2. Adjust the Gain of Nitsuki to suitability by manual when condition is Normal. - Adjust the standard illumination take within limit bright of Nitsuki and luminosity of SET into acount. - Exhortative Standard illumination, : High 70Cd/ , LOW BEAM : about 15Cd/ 5-2-3. Press the [S8]key of SVC remocon to adjustment of Whit Balance. X=0.288, Y=0.301 5-2-4. Memorize in Nitsuki after Adjustment of White Balance. 5-3. Adjustment of White Balance 5-3-1.Receive Nitsuki signal. 5-3-2.Adjust Picture to Normal mode. 5-3-3.The Adjustment of High Beam : Adjust R-DRIVE and G-DRIVE to R,G,B BAR come to center. 5-3-4.The Adjustment of Low Beam : Adjust R-BIAS and G-BIAS to R,G,B BAR come to center. 5-3-5.Repeat 5-3-3 and 5-3-4 to R,G,B BAR come to within center 1. 6.The adjustment of GEOMETRY 6-1. Press the [S-6]key on the SVC remocon to call up the Geometry mode. And then, Geometry OSD will be displayed. 6-1-1. All adjustment is base on PAL(50Hz), but it can be base on NTSC(60Hz) in case of need. 6-2. The adjustment of VERTICAL CENTER 6-2-1.Receive PAL RETMA pattern(signal of company:PAL-B 2CH). 6-2-2.Press the PR up/down Keys( ) to select V CENTER. Adjust with Vol Up/Down ( ) keys so that the center mark of the CRT may be located on the horizontal line in the middle of the pattern. In case of no center mark, adjust with Vol Up/Down ( ) keys to obtain a vertically symmetrical pattern.
-7-
|
|
|
> |
|
