|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
...instruction is ok.
...instrukcja jest ok.
Thanks/Dzięki
;
Documentation made available quickly and It is good quality. Thanks.
DTM-5.9
A B C D E
SCHEMATIC DIAGRAMS-4(SD-4)
POWER SUPPLY SECTION
P901
Refer to following table about the parts displayed by mark "LIST".
TYPE---> T901 T902 F901 F902 MDD NPT-1575D NPT-1520JQ 6A125V NONE 5A125V YES NONE YES NONE NONE
1
AC IN MDD : 120V, 60Hz
INLET
P902
U11
NAETC-9624
NAETC-9625 U12
5
F903 J904 J905 J907 J918 J930
TRANS. PRI. TERMINAL PC BOARD
POWER TRANS. T901
LIST 18 17 16 15 14 13 J930 LIST 5 THERMAL FUSE 12 11 10 TRANS. SEC. TERMINAL PCB
INLET PC BOARD
P922B P921B 6 4 7 3 8 2 P922A P921A 9 1
NAPS-9623 U10 POWER SUPPLY PC BOARD
C904 C903 + 100/35 2200/35 D907 NC R905 100K R906 C905 + 1 Vc 10/50 2 Vin 3 GND R907 4 Vout
F903 LIST
NC
INPUT VOLTAGE S901 240V J904 LIST F901 LIST
W type only
1 3
J931 NC NC
P910
2
P901A NC AC-H AC-G
AC OUTLETS SWITCHED
120V
J918 LIST
F902 LIST 7
To NAPS-9614 SD-1 : G4
82K 5 ADJ
+
C912 103M/275
9 8
T902 LIST
RL902
CAUTION
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH FUSE OF SAME TYPE AND RATING INDICATED. THIS SYMBOL LOCATED NEAR THE FUSE INDICATES THAT THE FUSE USED IS SLOW OPERATING TYPE FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE WITH SAME TYPE FUSE. FOR FUSE RATING REFER TO THE MARKING ADJACENT TO THE SYMBOL.
C902 104Z
D912 1SS355 Q912 KTC3199-GR R913 J905 LIST R915 220(1/2W) 1K R914 100K
A
V
ATTENTION
AFIN D'ASSURER UNE PROTECTION PERMANENTE CONTRE LES RISQUES D'INCENDIE, REMPLACER UNIQUEMENT PAR UN FUSIBLE DE MEME TYPE ET CALIBRATION COMME INDIQUE.
P913A JL911A P911A P912A NC
3
A
V
D913 1SS355
CE SYMBOLE INDIQUE QUE LE FUSIBLE UTLISE EST E LENT.POUR UNE PROTECTION PERMANENTE,N'UTILISER QUE DES FUSIBLES DE MEME TYPE. CE DARNIER EST INDIQUE LA QU LE PRESENT SYMBOL EST APPOSE.
NC
Q901 SI-3010KF
NOTE
TO NADG-9619
D901 100K D902 D901 - D909, D991, 992 : 1SS355 D903 D904 R908 10K
SD-2 : C5
J906
P911B P913B P912B NC
THE COMPONENTS IDENTIFIED BY MARK ! ARE CRITICAL FOR SAFETY REPLACE ONLY WITH PART NUMBER SPECIFIED. VOLTAGE (MEASURED WITH VOLTMETER) IS DC VOLTAGE.(NO INPUT SIGNAL). ALL PNP TRANSISTORS ARE EQUIVALENT TO 2SA1015-GR UNLESS OTHERWISE NOTED. ALL NPN TRANSISTORS ARE EQUIVALENT TO 2SC1815-GR UNLESS OTHERWISE NOTED. ALL DIODES ARE EQUIVALENT TO 1SS133 UNLESS OTHERWISE NOTED. ELECTROLYTIC CAPACITORS ( ) ARE IN uF/WV. ALL CAPACITORS ARE IN pF/50WV UNLESS OTHERWISE NOTED. EX) 030- 3pF 330- 33pF 331- 330pF 333- 0.033uF ALL RESISTORS ARE IN OHMS 1/4WATTS UNLESS OTHERWISE NOTED. THE THICK LINES ON PC BOARD ARE THE PRINTING SIDE OF THE PARTS. EX) PRINTING SIDE CIRCUIT IS SUBJECT TO CHANGE FOR IMPROVEMENT.
C907 100/35
1 GND_MPU 2 POWER 3 +10S 4 POFF 5
D905 C991 104Z D991 D906 J907 LIST
+22VS 6 GND_RL 7
DTM-5.9
4
D992 P991
D908 R909 100K D909 C906 4.7/50 D914 UDZS5.1B
<Note> NC = No mount of parts.
SD-Z : XY
Location of connected terminal in schematic diagrams. SD-Z = Schematic diagrams-Z. X = A to H, Y = 1 to 5.
|
|
|
> |
|
