|
|
|
Kto jest w sklepie?
Sklep przegląda 5292 gości i
15 zarejestrowanych klientów |
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
Adjusting Audio and Video Settings
Adjust the Output Level from the Speakers (Gain Setting) Expert
1 Audio2 Video Language General Audio DRC � Off Audio Out � 2 Channel Speaker Setting Gain Setting Fix Hi-Brid SACD � SACD Variable CD Digital Direct � Off Pure Audio Clock � Off Move SETUP Exit
This setting should be made when the Mulutichannel AUDIO OUT jacks on the rear panel are connected to an AV amplifier or receiver. The output level of each speaker in your system can be set and confirmed. The factory setting is set to "Fix". However, when you want to adjust the output level, select "Variable". When "Variable" is selected
1
1 Audio2 Video Language General Gain Setting Center Gain � Test Tone � Move �/+
L R SW LS RS ENTER
Move the cursor control joystick right or left to select a speaker.
Front Left, Center, Front Right, Surround Left, Surround Right, Subwoofer, Front Left, ... Speakers set to "Off" in the [Speaker Setting] setting cannot be selected. Move the cursor control joystick down.
0.0dB Off
Select
SETUP
Return Exit
2
Move the cursor control joystick right or left to set the output level.
The value can be adjusted in the range of -6.0 dB to 6.0 dB in 0.5 dB increments. The output level of front L/R speakers are fixed and therefore cannot be adjusted.
3 4
Repeat steps 1 and 2 for each speaker in your system.
Move the cursor control joystick down.
Move the cursor control joystick right or left to output the test tone to confirm the output levels.
Off :Test tone is not output. (Factory Setting) On :Test tone output is manually controlled. Auto :Test tone is automatically output. When "On" is selected Move the cursor control joystick up to the speaker selection line, then Move the cursor control joystick right or left to select the speaker to output the test tone from. The test tone is output from the selected speaker. To output the test tone from another speaker, change the speaker selection. When "Auto" is selected Test tone is output in the following order. Front Left, Center, Front Right, Surround Left, Surround Right, Front Left, ...
5
Move the cursor control joystick up to the [Gain] setting, then move the cursor control joystick right or left to adjust the output level while listening to the test tone.
ADJUSTING AUDIO AND VIDEO SETTINGS
To stop the test tone Move the cursor control joystick down to the [Test Tone] setting, then move the cursor control joystick right or left to select "Off" in the [Test Tone] setting.
Notes � When "Variable" is selected, the output level of all speakers is uniformly set to �6.0 dB. The output level of each speaker (center, surround, or sub woofer) can then be adjusted in the range of �6.0 dB to 6.0 dB. "6.0 dB" is the maximum level of "Variable" and also the level set for "Fix". Therefore, when "Variable" is selected, the output level will usually be lower than when the setting is set to "Fix". � The "Variable" setting has no effect on CD and Video CD playback. � The test tone is not output when the setting is set to "2 Channel" in the [Audio Out] setting (page 31), while the disc tray opens, or while a disc is playing.
33
En
|
|
|
> |
|
