PHILIPS DVD728/51
Instrukcja Serwisowa

Safety Instructions, Warnings, Notes, and Service Hints

DVD728-731 /0X1

2.

EN 3

2. Safety Instructions, Warnings, Notes, and Service Hints
2.1
2.1.1

Safety Instructions
General Safety Safety regulations require that during a repair: � Connect the unit to the mains via an isolation transformer. � Replace safety components, indicated by the symbol �, only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the following points: � Route the wires/cables correctly, and fix them with the mounted cable clamps. � Check the insulation of the mains lead for external damage. � Check the electrical DC resistance between the mains plug and the secondary side: 1. Unplug the mains cord, and connect a wire between the two pins of the mains plug. 2. Set the mains switch to the 'on' position (keep the mains cord unplugged!). 3. Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom. 4. Repair or correct unit when the resistance measurement is less than 1 M�. 5. Verify this, before you return the unit to the customer/ user (ref. UL-standard no. 1492). 6. Switch the unit �off�, and remove the wire between the two pins of the mains plug.

2.2
2.2.1

Warnings
General � All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD, �). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: � Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. � Wristband tester 4822 344 13999. Be careful during measurements in the live voltage section. The primary side of the power supply (pos. 1005), including the heatsink, carries live mains voltage when you connect the player to the mains (even when the player is 'off'!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A 'lightning stroke' and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply. Never replace modules, or components, while the unit is �on�.

�

�

2.2.2

Laser � � � The use of optical instruments with this product, will increase eye hazard. Only qualified service personnel may remove the cover or attempt to service this device, due to possible eye injury. Repair handling should take place as much as possible with a disc loaded inside the player. Text below is placed inside the unit, on the laser cover shield:

2.1.2

Laser Safety This unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (due to possible eye injury). Laser Device Unit Type Wavelength Output Power

�

: Semiconductor laser GaAlAs : 650 nm (DVD) : 780 nm (VCD/CD) : 20 mW (DVD+RW writing) : 0.8 mW (DVD reading) : 0.3 mW (VCD/CD reading) : 60 degree

CAUTION VISIBLE AND INVISIBLE LASER RADIATI ON WHEN OPEN AVO ID EXPOSURE TO BEAM ADVARSEL SYNLIG OG USYNLIG LASERSTR�LING VED �BNING UNDG� UDS�TTELSE FOR STR�LING ADVARSEL SYNLIG OG USYNLIG LASERSTR�LING N�R DEKSEL �PNES UNNG� EKSPONERING FOR STR�LEN ! VARNING SYNLIG OCH OSYNLIG LASERSTR�LNING N�R DENNA DEL �R �PPNAD BETRAKTA EJ STR�LEN VARO! AVATT AESSA OLET ALTTIINA N�KYV�LLE JA N�KYM�TT �M�LLE LASER S�TEILYLLE. �L� KAT SO S�T EESEEN VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GE�FFNET NICHT DEM STRAHL AUSSETSEN DANGER VISIBLE AND INVISIBLE LASER RADIATI ON WHEN OPEN AVO ID DIRECT EXPOSURE TO BEAM AT TENTION RAYO NNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU

Figure 2-2 2.2.3 Notes Dolby Manufactered under licence from Dolby Laboratories. �Dolby�, �Pro Logic� and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved.

Beam divergence

Figure 2-3 Figure 2-1 Trusurround TRUSURROUND, SRS and symbol (fig 2-4) are trademarks of SRS Labs, Inc. TRUSURROUND technology is manufactured under licence frm SRS labs, Inc.

Note: Use of controls or adjustments or performance of procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam.

Figure 2-4