|
Kto jest w sklepie?
Sklep przegląda 6043 gości
|
Kategorie
|
Informacje
|
Polecamy
|
|
|
|
|
Dla tego produktu nie napisano jeszcze recenzji!
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
;
...instrukcja serwisowa w pełni czytelna i kompletna. Dziękuję!
0. Disc Check Memory
Disc Check
1. SL Disc Check 2. CD Disc Check 3. DL Disc Check
0. Reset SLED TILT
Disc Type Disc Type Auto Check DVD SL 12 cm DVD DL 12 cm CD 12cm SACD 12 cm DVD SL 8 cm DVD DL 8 cm CD 8 cm SACD 8 cm Reset SLED TILT TC. : : EMG. 00 CD 12 cm 1. 2. 3. 4. 5. 6. 7. 8. 9. 0.
Display when CD 12cm disc was selected
On this screen, the mirror time is measured to judge the disc and it is written to the EEPROM. First load DVD SL disc and press [1], next load CD disc and press [2], and finally load DVD DL disc and press [3]. The adjustment must be executed more than once after default data were written. External vibration or shock to the player must not be given. Reference value for DVD is from 10 to 20, and for CD, from 28 to 4F. Check that the value of CD is larger than that of DVD. When those values are beyond a range perform this adjustment again. From this screen, you can go to another mode by pressing [NEXT] or [PREV] key, but you cannot enter this mode from another mode. You can enter this mode from the Operation Menu screen only.
[0] Reset SLED TILT [1] Disk Type Check
Reset the Sled and Tilt to initial position. Judge automatically the loaded disc. As the judged result is displayed at the bottom of screen, make sure that it is correct. If Disc Check Memory menu has not been executed after EEPROM default setting, the disc type cannot be judged. In this case, return to the initial menu and make a check for three types of discs (SL, DL, CD). Select the loaded disc. The adjusted value is written to the address of selected disc. No further entry is necessary if [1] was selected.
[2] to [9] 1. Disc Type
1. 2. 3. 4. 5. 6. 7. 8. 9. 0. Disc Type Disc Type Auto Check DVD SL 12 cm DVD DL 12 cm CD 12cm SACD 12 cm DVD SL 8 cm DVD DL 8 cm CD 8 cm SACD 8 cm Reset SLED TILT EMG. 00
2. Servo Control
Servo Control LD Off R.Sled FWD SP Off L.Sled REV Focus Off TRK. Off Sled Off CLVA Off FCS. Srch Off
1. 2. 3. 4. 5. 6. 7.
On this screen, select the disc type. To select the disc type, press the number of the loaded disc. The selected disc type is displayed at the bottom. Selecting [1] automatically selects and displays the disc type. In case of wrong display, retry �Disc Check Memory�. Also, opening the tray causes the set disc type to be cleared. In this case, set the disc type again after loading. In performing manual operation, the disc type must be set. Once the disc type has been selected, the sector address or time code display field will appear as shown below. These values are displayed when PLL is locked.
Disc Type Disc Type Auto Check DVD SL 12 cm DVD DL 12 cm CD 12cm SACD 12 cm DVD SL 8 cm DVD DL 8 cm CD 8 cm SACD 8 cm Reset SLED TILT SA. SI. EMG. 00 DVD SL 12 cm 1. 2. 3. 4. 5. 6. 7. 8. 9. 0.
0. Reset SLED TILT SA. SI. DVD SL 12 cm
EMG. 00
On this screen, the servo on/off control necessary for replay is executed. Normally, turn on each servo from 1 sequentially and when CLVA is turned on, the usual trace mode becomes active. In the trace mode, DVD sector address or CD time code is displayed. This is not displayed where the spindle is not locked. The spindle could run overriding the control if the spindle system is faulty or RF is not present. In such a case, do not operate CLVA.
Display when DVD SL 12cm disc was selected
6-8
|
|
|
> |
|