KENWOOD DVR6300
Instrukcja Serwisowa

DVR-6300
CONTENTS / ACCESSORIES / CAUTIONS
CONTENTS
CONTENTS / ACCESSORIES / CAUTIONS...............2 PARTS DESCRIPTIONS .............................................3 PC BOARD ..................................................................4 SCHEMATIC DIAGRAM ............................................15 EXPLODED VIEW .....................................................25 PARTS LIST...............................................................27 SPECIFICATIONS .....................................................34

ACCESSORIES
FM indoor antenna (1) (For Europe) (T90-0916-08) (For U.S.A., Canada and Australia) (T90-0915-08) Loop antenna (1) (T90-0917-08) Accessories for speaker part (For DVT-6300 and DVT-7300) Speaker cords (6) *
For Front (2) For Center (1) For Rear (2) For Subwoofer (1) Length 4.5 m (177-3/16") 3 m (118-1/8") 8 m (314-15/16") 4.5 m (177-3/16")

Video cord (Yellow)(1) (E30-7341-08)

Remote control unit (1) (A70-1685-08)

Batteries (R03/AAA) (2)

Cushion (15) * (Small : 11 pcs 1 sheet) (Big : 4 pcs 1 sheet)

SYSTEM CONFIGURATIONS
SYSTEM DVT-6300-H DVT-6300-S DVT-7300 DVT-8300 RECEIVER DVR-6300 DVR-6300 DVR-6300 DVR-6300 SPEAKER KSW-6300-H KSW-6300-S KSW-7300 KS-908HT SPEAKER SW-18HT

* See speaker�s manual.

CAUTIONS
Operation to reset
The microprocessor may fall into malfunction (impossibility to operate erroneous display, etc.) when the power cord is unplugged while power is ON or due to an external factor. In this case, switch off the power, wait for several seconds, and then switch the power on again.

Note related to transportation and movement
Before transporting or moving this unit, carry out the following operations. 1. Set the POWER ON/OFF switch to the ON without loading a disc. 2. Wait a few seconds and verify that the display shown appears. "NO DISC"

For the U.S.A.
CAUTION:
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, the following are reproductions of labels on, or inside the product relating to laser product safety. KENWOOD CORPORATION 2967-3, ISHIKAWA-CHO, HACHIOJI-SHI, TOKYO, JAPAN KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS NO. 21 CFR 1040.10, CHAPTER 1, SUBCHAPTER J.

3. Set the POWER ON/OFF switch to OFF.

Caution on condensation
Condensation (of dew) may occur inside the unit when there is a great difference in temperature between this unit and the outside. This unit may not function properly if condensation occurs. In this case, leave the unit for a few hours and restart the operation after the condensation has dried up. Be specially cautious against condensation in the following circumstances: When this unit is carried from one place to another across a large difference in temperature, when the humidity in the room where this unit is installed increases, etc.

Location: Back Panel

For the U.S.A.
Note to CATV system installer
This reminder is provided to call the CATV system installer�s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

The marking of products using lasers
(For countries other than U.S.A. and Canada)
CLASS 1 LASER PRODUCT The marking this product has been classified as Class 1. It means that there is no danger of hazardous radiation outside the product. Location: Back panel

For Canada
2
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.