|
Kto jest w sklepie?
Sklep przegląda 5769 gości
|
Kategorie
|
Informacje
|
Polecamy
|
|
|
|
|
Dla tego produktu nie napisano jeszcze recenzji!
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
;
Instrukcja bardzo czytelna. zawiera co potrzeba. Polecam
;
...instrukcja serwisowa w pełni czytelna i kompletna. Dziękuję!
(ABC
MARK/CUE:MARK mFREEZE:OFF CHG REEL NO: (YESm4)
3
Press the MENU/STATUS switch to move the text entry arrow. Press the MENU/STATUS switch upward to move the cursor to the right or downward to move it to the left.
Item
Settings
MARK/CUE MARK (normal value), CUE Selects MARK See �Using the ClipLink Function� mode or CUE mode (page 41). FREEZE See �Using the Freeze Mix Function� Sets the freeze mix (page 44). function. CHG REEL NO Sets the cassette name/number
Chapter 4 Viewfinder Screen Indications and Menus
4
Press the UP/ON button or DOWN/OFF button to enter the desired characters. The displayed character changes each time the UP/ ON button is pressed. It changes in reverse order each time the DOWN/OFF button is pressed.
See �To set the cassette name/ number� below.
To set the cassette name/number (when using DSR-1/1P)
5 6
Return to step 2 and repeat the text entry procedure. After completing text entry, move the text entry cursor to the parenthesis position. The display changes as follows.
1 2
Connect the DSR-1/1P and load a cassette. Press the MENU/STATUS switch to move the cursor to CHG REEL NO, then press the UP/ON button.
MARK/CUE:MARK FREEZE:OFF mC H G R E E L N O : ( Y E S m4)
7
The cursor (�) changes to the text entry arrow (�) and the current cassette name/number is displayed. (�NO TAPE� is displayed if you neglected to load a cassette.)
Check your cassette name/number setting, and press the UP/ON button if no more changes are required. (To make changes or to abort the procedure for this setting, return to step 2.) This writes the new cassette name/number to the cassette memory, after which the display changes as follows.
54
Chapter 4
Viewfinder Screen Indications and Menus
�
1-34 DXC-D30WS/P(E)/V1
Viewfinder Basic Menu
Basic menu page 7
The following display is shown when the DSR-1/1P is connected.
MARK/CUE:MARK FREEZE:OFF CHG REEL NO: )
Basic menu pages 8 and 9
You can create a title of up to four lines, each of twelve alphanumeric or punctuation characters, and
Current cassette name/number
4
Press the UP/ON button to select the required character. Each time you press the UP/ON button, the character cycles through the following sequence.
ABCDEFGHIJKLMNOPQRSTUVWXYZ?;x/0123456789: -., (Space)
then save it. It is then possible to record the title over the picture while shooting. Entering the title (page 8)
1
Press the MENU/STATUS switch as necessary to display basic menu page 8 (title setting display) in the viewfinder.
To reverse the character sequence With the UP/ON button held down, press the DOWN/OFF button.
5
Press the DOWN/OFF button to confirm the character selection. The cursor advances to the next character position. To change a character after confirming it Return to step 3, and input the character again.
mTITLE SET?
6
If a title is already present, it appears on this screen. To delete the displayed title, press the UP/ ON and DOWN/OFF buttons simultaneously.
Repeat steps 4 and 5 until the title is complete.
DXC-D30
Chapter 4 Viewfinder Screen Indications and Menus
2
Press the UP/ON button. This brings up the cursor on the screen (flashing), and switches to title editing mode.
Initial cursor position
7
When the title is complete, press the MENU/ STATUS switch as necessary to return to the normal viewfinder indications. The title created is retained, even when you power the camera off.
MARK/CUE:MARK FREEZE:OFF CHG REEL NO: mW R I T E ? ( Y E S m4) (DEF )
To record a title (page 9)
1
Press the MENU/STATUS switch as necessary to access basic menu page 9 (title display).
3
Press the DOWN/OFF button to move the cursor to the position where you wish to insert a character. To move the cursor back With the DOWN/OFF button held down, press the UP/ON button.
mTITLE IND?
(continued)
Chapter 4
Viewfinder Screen Indications and Menus
55
|
|
|
> |
|