|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 ;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
;
Bardzo dobra instrukcja. Zawiera wszystko co potrzeba, polecam!
;
Instrukcja jest OK. Schematy czytelne, opisane niektóre procedury.
Troubleshooting > Messages and Troubleshooting
Message
Data error in all image file. Repair all data now? YES NO
Cause/condition for message to appear
Appears if writing to file cannot be completed normally because power was turned off by mistake during video recording or editing, and it is recognized that the video file must be totally repaired. Also appears when condensation occurs on lens or drive of DZ-MV580A/MV550A. Condensation will occur when the DZMV580A/MV550A is moved form a cold place to a warm place. Appears if the self-diagnosis function in DZ-MV580A/MV550A detects a serious problem. This message appears during normal operation process, when DZ-MV580A/ MV550A checks whether a proper disc has been loaded or not. It is displayed for a longer time period when the date has changed. This message appears during normal operation process, when the recorded images are being stored on disc. Appears if the remaining video recordable time on disc is less than 10 minutes, or the remaining number of recordable photos is less than 10. Appears when the disc has been edited on a device other than DZ-MV580A/ MV550A, and mismatch has occurred in recorded data. Also appears when reading or writing from/to recorded file cannot be performed because the disc is dirty. Appears when the disc could not be finalized because it was dirty. Appears if accident, such as power off, has occurred during finalizing.
Troubleshooting
Choose �YES� and designate total repair (automatic repair) of video file. Choosing �NO� will display a message for verifying initialization. [Refer to *3 page 4-14] Do not execute repair, but set the power switch to �POWER OFF� with the disc loaded, and then leave the DZ-MV580A/MV550A in a dry place until condensation disappears (usually 1-2 hours). Take note of the 4-digit alphanumerals in ����, and refer to �4-5 Self-Diagnosis Function and Troubelshooting�. Operate DZ-MV580A/MV550A after the message disappears.
DISC ���� (4-digit alpha-numerals showing the code of trouble will appear in ����.) DISC ACCESS
Operate DZ-MV580A/MV550A after the message disappears. Delete unnecessary scenes, or replace the disc.
DISC ALMOST FULL
Disc error
Format the disc (deleting all recorded data), or replace the disc.
Clean the disc, or replace it. [Refer to page 4-14] Clean the disc, or replace it. [Refer to page 4-14] Set the power switch to �POWER OFF� and reconnect the AC adapter/ charger; then set the power switch to �VIDEO� and start finalizing again. Or press the DISC EJECT button, reload the disc, and then execute finalizing. Replace the disc.
Disc error has occurred. Finalizing is not complete.
If the message still appears even when the disc has been cleaned and finalized again and again, the disc may be defective.
4 - 15
|
|
|
> |
|
