PANASONIC ES8075
Instrukcja Obsługi

You can always connect your shaver to the self-cleaning recharger or the adaptor to maintain full battery capacity. This shaver cannot be overcharged. Before travelling, charge it fully for 1 hour if you will not be taking the adaptor with you.

Do not place fingers on the On/Off switch during use. This may cause the shaver to stop during use or change it to the �sonic� vibration cleaning mode. Place your finger on the finger rest during use. Hold the shaver at a right angle (90°) to your skin (see fig. 6). Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave. Pivot action selector (see fig. 7) Use the pivot action selector to choose the shaving mode, �soft� (soft) and �lock� (lock) based on your shaving preference. The pivot action can be changed whether the switch is turned on or off. System outer foil (see fig. 8) System outer foil has a slit blade (a) between 2 foils (b). They move up and down independently to follow the contours of your face. The slit blade catches and cuts longer and lying hairs easily.

among many other shaving aids (gel, soap, cream, etc.). Do not put a thick layer of shaving foam as it may affect shaver�s performance. If the shaving head is clogged with foam, simply rinse it under running water.

Using the trimmer
(see fig. 9) Slide the trimmer handle up to open the trimmer. Place the trimmer at a right angle to your skin and move it downward to trim sideburns.

Charging without selfcleaning recharger
Connect the power cord to the shaver, and plug the adaptor to an AC outlet (see fig. 5). The shaver will be adjusted automatically to voltages between 100-240V AC. In some areas, a special plug adaptor may be required.

Cleaning your shaver
1 Cleaning with the self-cleaning recharger Preparing the self-cleaning recharger Warning � Do not wash or apply water to the adaptor or self-cleaning recharger. Failure to observe this may cause electric shock or result in short circuits. 1. Detach the shaver and the appliance plug from the self-cleaning recharger. 2. Fill the water tank with water. 1) Remove the water tank from the self-cleaning recharger (see fig. 10-1). 2) Open the water tank cap (see fig. 10-2). 3) Wash away the old cleaning liquid inside the water tank and rinse (see fig. 11). 4) Pour tap water up until the feed water line (see fig. 12).

Using your shaver
Caution � The system outer foil is very thin and can be damaged if handled improperly. Before each use, always check the foil for damage. To avoid personal injury, do not use if the foil or other parts of the shaving head are damaged. Push the On/Off switch to turn the shaver on. If you push and hold the On/Off switch for more than 2 seconds, it will activate the turbo mode for �sonic� vibration cleaning. (see �Cleaning your shaver without the self-cleaning recharger�) Shaving with �sonic� vibration may damage your skin. Please turn it off and on again to deactivate the turbo mode.

For wet shaving
Put a thin layer of shaving foam on your face which works as a lubricant. Shaving foam is the most suitable

* Do not pour water over the water feed line in the tank. This may cause the cleaning liquid to spill. 3. Firmly shut the water tank cap and attach the tank to the selfcleaning recharger (see fig. 13). 4. Peel off the seals from the new detergent cartridge (two seals) (see fig. 14). � Hold the detergent cartridge horizontally. (The detergent may spill if tilted excessively.) 5. Attach the detergent cartridge to the self-cleaning recharger (see fig. 15). � Do not use any solution other than the Panasonic Shaver self-cleaning recharger special detergent. � Be sure to change the detergent cartridge and the cleaning liquid inside the water tank simultaneously. Adding water, or changing just the detergent cartridge or the water, will result in deteriorated cleaning functions. � When the self-cleaning recharger is operated, the concentrated detergent inside the cartridge will be diluted and the water inside the tank will become a cleaning liquid. Cleaning your shaver 1. Insert the appliance plug into the self-cleaning recharger socket (see fig. 16-1). 2. Firmly insert the adaptor into the AC outlet (see fig. 16-2).

10

10

11

11