|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
 ;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
;
Wszystko w porządku.
Instrukcja czytelna i kompletna.
Dziękuję.
all right!
thank you.
FO-1660MTH
7. Use of Document Carrier Sheet
A document carrier sheet must be used for the following documents.
TELEPHONE JACK
A standard telephone jack must be located near the machine. This is the telephone jack commonly used in most homes and offices.
� � �
Those with tears. Those smaller than size 148 mm (W) x 128 mm (L). Carbon-backed documents
�
Plugging the fax machine into a jack which is not an jack may result in damage to the machine or your telephone system. If you do not know what kind of jack you have, or needed to have one installed, contact the telephone company.
Make print straight across paper E.G. Place the document carrier in the document feeder with the clear film side down
2. Loading the imaging film (FO-15CR)
1Press the release marked OPEN and open the print compartment
cover.
�
Caution! The printing head (the strip of metal on the underside of the cover) applies heat to the printing film. It may be hot if a document has just been printed.
Direction of insertion
NOTE: To transmit a carbon-backed document, insert a white sheet of paper between the carbon back of the document and the document carrier.
�
Those containing an easily separable writing substance (e.g., tracing paper written on with a soft, heavy lead pencil).
NOTES:
� � �
When using the document carrier, carefully read the instructions written on the back. If the document carrier is dirty, clean it with a soft, moist cloth, and then dry it before using for transmission. Do not place more than one document in the carrier at a time.
[4] Installation
1. Site selection
Take the following points into consideration when selecting a site for this model.
ENVIRONMENT
� � �
The machine must be installed on a level surface. Keep the machine away from air conditioners, heaters, direct sunlight, and dust. Provide easy access to the front, back, and sides of the machine. In particular, keep the area in front of the machine clear, or the original document may jam as it comes out after scanning. The temperature should be between 5° and 35°C. The humidity should be between 30% and 85% (without condensation).
� �
2If you are replacing the imaging film, take the old film out of the print-
ing compartment and remove the three (3) green gears and the green flange from the ends of the spools. DO NOT DISCARD THE GREEN GEARS AND THE GREEN FLANGE!
ELECTRICITY
Standard local voltage, grounded AC outlet is required.
Caution!
� �
Connection to a power source other than that specified will cause damage to the equipment and is not covered under the warranty. If your area experiences a high incidence of lightning or power surges, we recommend that you install a surge protector for the power and telephone lines. Surge protectors can be purchased at most telephone specialty stores.
If the machine is moved from a cold to a warm place...
If the machine is moved from a cold to a warm place, it is possible that the reading glass may fog up, preventing proper scanning of documents for transmission. To remove the fog, turn on the power and wait approximately 2 hours before using the machine.
1�4
|
|
|
> |
|
