JVC FSMD9000
Instrukcja Obsługi

English

s s s

You can place an 8 cm (3'') CD without an adaptor. If the CD cannot be read correctly (because it is scratched, for example), " 0 0:00" appears on the display. You can insert a CD while listening to the other source.

PROGRAM

Basics of Using the CD Player-Normal Play
To Play a CD ������������

s Press the UP, DOWN, >, or < button to 5.
select the track to program.
UP button: Increases the track number by 1. DOWN button: Decreases the track number by 1. > button: Increases the tenth digit of the track number. < button: Decreases the tenth digit of the track number. Example: for track 2, press the UP button twice. For track 12, press the > button, then press the UP button twice (or simply press the UP button 12 times).
Program order number

s Insert a CD. 1. s Press the CD 38 button. 2.
The first track of the CD begins playing.

�

s Press the SET button. 6.
Track number Playback time
UP

� �

The track number that has been played disappears from the music calender. The CD Player automatically stops when the last track of the

SET

(After 2 seconds)

DOWN

CD has finished playing. To stop playing the CD, press the 7 button. The following information for the CD is displayed.

Total playback time of the programmed tracks

s Repeat steps 5 and 6 to select the other 7.
tracks for the program.
Total track number Total playback time

To stop playing and remove the CD, press the CD0 button to open the CD holder. To pause, press the CD38 button. The playback time blinks on the display. To cancel pause, press the same button again. Play continues from the point where it was paused.

You can see the total playback time of programmed tracks on the display. Also, you can see the programmed tracks on the music calender.

s Press the CD 38 button. 8.
The System plays the tracks in the order you have programmed them. s You can skip to a particular program track by pressing the 4 or ¢ button during Program Play. s To stop playing, press the 7 button once. To confirm the programmed tracks while the CD player is stopped, press the 4 or ¢ button; the tracks making up the program will successively be displayed in the programmed order. To delete all the tracks in the program, press the 7 button repeatedly until all the tracks are cleared. Turning off the power or pressing the CD 0 button to open the CD holder will also clear the programmed tracks. To exit the program mode once, while the CD Player is stopped, press the PROGRAM button to light off the "CD PROGRAM" indicator. Notes: � If the total playback time of the programmed tracks exceeds 99 minutes 59 seconds, the total playback time will go out on the display. When the CD contains more than 21 tracks: When you try to program a track number exceeding 20 (for example the 25th track), the total playback time indication will go out, though programming is possible.

To Select a Track or Passage within a Track ��������������
During playback, press the 4 or ¢ button to select the track you want. The selected track starts playing. � 3UHVVýWKHý¢ýEXWWRQýRQFHýWRýVNLSýWRýWKHýEHJLQQLQJýRIýWKHý QH[WýWUDFNï � 3UHVVýWKHý4ýEXWWRQýWRýVNLSýWRýWKHýEHJLQQLQJýRIýWKHýWUDFNýEHð LQJýSOD\HGïý3UHVVýWZLFHýTXLFNO\ýWRýVNLSýWRýWKHýEHJLQQLQJýRIý WKHýSUHYLRXVýWUDFNï

Search Play ������������
Holding down the 4 or ¢ button, during playback, will fast forward/backwards the CD so you can quickly find a particular passage in the track you are listening to.

Programming the Playing Order of the Tracks
You can program the playing order of the tracks using the Remote Control.

�

To Modify the Program �������
Modify the contents of the program while the CD Player is stopped. Each time you press the 7 button, the last track in the program is deleted. To add new tracks to the end of the program, repeat above steps 5 to 7.

s s

You can program up to 20 tracks in any desired order including the same tracks. You can only make a program when the CD Player is stopped.

s Insert a CD. 1. s Press the CD 38 button. 2. s Press the 7 button to stop the CD. 3. s Press the PROGRAM button. 4.
The System enters the programming mode and the �CD PROGRAM� indicator lights up.

Random Play
The tracks will play in no special order when you use this mode.

s Press the RANDOM button on the Remote 1.
Control.
The "CD RANDOM" indicator lights up on the display.

10