ROLAND G-70
Instrukcja Obsługi

G-70 Music Workstation r Appendix | MFX and IFX types and parameters

G Cutoff Frequency (200~8000Hz)�Basic frequency of the filter. G Pre Delay (0.0~100.0ms)�Adjusts the delay time from when the direct sound begins until the flanger sound is heard. G Rate [sync] (Hz, Note)�Use this parameter to specify whether (�Note�) or not (�Hz�) the modulation rate should be synchronized to the Arranger or Recorder tempo. Depending on your choice, the setting range of the following parameter refers to a speed (Hz) or a note value. G Rate [Hz] (0.05~10.00Hz)�Frequency, i.e. modulation speed. G Rate [note] (musical notes)�Rate parameters can be set as a note-value of a tempo if you set the �Sync� parameter above to �Note�. Specify the value of the desired note. G Depth (0~127)�Depth of modulation. G Phase (0~180 deg)�Spatial spread of the sound. G Feedback (�98%~0~+98%)�Adjusts the proportion of the flanger sound that is fed back into the effect. Negative (�) settings will invert the phase. G Step Rate [sync] (Hz, Note)�Use this parameter to specify whether (�Note�) or not (�Hz�) the step rate should be synchronized to the Arranger or Recorder tempo. Depending on your choice, the setting range of the following parameter refers to a speed (Hz) or a note value. G Step Rate [Hz] (0.10~20.00Hz)�Rate (period) of pitch change. G Step Rate [note] (musical notes)�Rate parameters can be set as a note-value of a tempo if you set the �Sync� parameter above to �Note�. Specify the value of the desired note. G Output Mode (Speaker, Phones)�Adjusts the method that will be used to hear the sound that is output to the OUTPUT jacks. The optimal 3D effect will be achieved if you select SPEAKER when using speakers or PHONES when using headphones. G EQ Low Gain (�15dB~0~15dB)�Gain of the low frequency range. G EQ High Gain (-15dB~0~15dB)�Gain of the high frequency range. G Balance (D100:0W, D50:50W, D0:100W)�Volume balance between the direct (D) and the effect sound (W). G Level (0~127)�Output level. 61. Band Chorus A chorus effect that lets you apply an effect independently to the low-frequency and high-frequency ranges. G Split Frequency (200~8000Hz)�Frequency at which the low and high ranges will be divided. G Low Pre Delay (0.0~100.0ms)�Delay time from when the original sound is heard to when the low-range chorus sound is heard. G Low Rate [sync] (Hz, Note)�Use this parameter to specify whether (�Note�) or not (�Hz�) the low modulation rate should be synchronized to the Arranger or Recorder tempo. Depending on your choice, the setting range of the following parameter refers to a speed (Hz) or a note value. G Low Rate [Hz] (0.05~10.00Hz)�Rate at which the lowrange chorus sound is modulated. G Low Rate [note] (Musical Notes)�Rate parameters can be set as a note-value of a tempo if you set the �Sync� parameter above to �Note�. Specify the value of the desired note. G Low Depth (0~127)�Modulation depth for the low-range chorus sound.

G Low Phase (0~180 deg)�Spaciousness of the low-range chorus sound. G High Pre Delay (0.0~100.0ms)�Delay time from when the original sound is heard to when the high-range chorus sound is heard. G High Rate [sync] (Hz, Note)�Use this parameter to specify whether (�Note�) or not (�Hz�) the high modulation rate should be synchronized to the Arranger or Recorder tempo. Depending on your choice, the setting range of the following parameter refers to a speed (Hz) or a note value. G High Rate [Hz] (0.05~10.00Hz)�Rate at which the highrange chorus sound is modulated G High Rate [note] (musical notes)�Rate parameters can be set as a note-value of a tempo if you set the �Sync� parameter above to �Note�. Specify the value of the desired note. G High Depth (0~127)�Modulation depth for the highrange chorus sound. G High Phase (0~180 deg)�Spaciousness of the high-range chorus sound. G Balance (D100:0W, D50:50W, D0:100W)�Volume balance between the direct sound (D) and the chorus sound (W). G Level (0~127)�Output level. 62. Band Flanger A flanger that lets you apply an effect independently to the low-frequency and high-frequency ranges. G Split Frequency (200~8000Hz)�Frequency at which the low and high ranges will be divided. G Low Pre Delay (0.0~100.0ms)�Delay time from when the original sound is heard to when the low-range flanger sound is heard. G Low Rate [sync] (Hz, Note)�Use this parameter to specify whether (�Note�) or not (�Hz�) the low modulation rate should be synchronized to the Arranger or Recorder tempo. Depending on your choice, the setting range of the following parameter refers to a speed (Hz) or a note value. G Low Rate [Hz] (0.05~10.00Hz)�Rate at which the lowrange flanger sound is modulated. G Low Rate [note] (Musical Notes)�Rate parameters can be set as a note-value of a tempo if you set the �Sync� parameter above to �Note�. Specify the value of the desired note. G Low Depth (0~127)�Modulation depth for the low-range flanger sound. G Low Phase (0~180 deg)�Spaciousness of the low-range flanger sound. G Low Feedback (�98%~0~+98%)�Proportion of the lowrange flanger sound that is to be returned to the input (negative values invert the phase). G High Pre Delay (0.0~100.0ms)�Delay time from when the original sound is heard to when the high-range flanger sound is heard. G High Rate [sync] (Hz, Note)�Use this parameter to specify whether (�Note�) or not (�Hz�) the high modulation rate should be synchronized to the Arranger or Recorder tempo. Depending on your choice, the setting range of the following parameter refers to a speed (Hz) or a note value. G High Rate [Hz] (0.05~10.00Hz)�Rate at which the highrange flanger sound is modulated. G High Rate [note] (musical notes)�Rate parameters can be set as a note-value of a tempo if you set the �Sync� parameter above to �Note�. Specify the value of the desired note.

241