CASIO G7210-1V
Instrukcja Obsługi

MO0310-EA

Operation Guide 2816
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to carefully read this manual and keep it on hand for later reference when necessary. Expose the watch to bright light to charge its battery before using it. You can use this watch even as its battery is being charged by exposure to bright light. � Be sure to read �Battery� of this manual for important information you need to know when exposing the watch to bright light.

About This Manual
� Button operations are indicated using the letters shown in the illustration. � Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be found in the �Reference� section.

If the display of the watch is blank...
If the SLEEP indicator is on the display, it means that the display is blank because the watch�s Power Saving function has turned off the display to conserve power. Power Saving automatically turns off the display and enters a sleep state whenever your watch is left for a certain period where it is dark. � The initial factory default setting is Power Saving on. � The watch recovers from the sleep state if you move it to a well-lit area*, if you press any button, or if you angle the watch towards your face for reading. * It can take up to five seconds for the display to turn on. � See �Power Saving Function� for more information.

(Light)

General Guide
� Press C to change from mode to mode. � In any mode, press L to illuminate the display. Countdown Timer Mode Alarm Mode

L

L

Timekeeping Mode Press C. Dual Time Mode Stopwatch Mode

Timekeeping
Hour : Minutes Seconds PM indicator

Use the Timekeeping Mode to set and view the current time and date.

To set the time and date 1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen. 2. Press C to move the flashing in the sequence shown below to select other settings.
Day of week Month � Day
Seconds Hour Day Minutes 12/24-Hour Format Year

Timer Mode The countdown timer gives you a choice of two modes: auto-repeat and elapsed time. Auto-repeat The auto-repeat mode automatically restarts the countdown from the countdown start time you set whenever zero is reached. � The auto-repeat mode is best when timing the starts of match races. � Even if you start a countdown operation from the reset time, the countdown automatically restarts from the countdown start time whenever it reaches zero. � Auto repeat timing repeats up to seven times.

L

Power Saving

Month

Elapsed Time When the end of the countdown is reached in the elapsed time mode, the timer automatically switches to an elapsed time measurement operation. � The elapsed time mode is best when timing the speed of yachts during ocean races. � The elapsed time operation is performed in one-second increments up to 99 hours, 59 minutes, 59 seconds.

3. When the setting you want to change is flashing, use D and B to change it as described below. Setting Seconds Hour, Minutes, Year, Month, Day 12/24-Hour Format Power Saving Screen Button Operations Press D to reset to 00. Use D (+) and B (�) to change the setting. Press D to toggle between 12-hour (12H) and 24-hour (24H) timekeeping. Press D to toggle Power Saving on (ON) and off (OFF).

Countdown Timer Beeper Operations

The watch beeps at various times during a countdown so you can keep informed about the countdown status without looking at the display. The following describes the types of beeper operations the watch performs during a countdown. Countdown End Beeper The watch beeps each second of the final 10 seconds before a countdown reaches zero, and at zero. The first five beeps (seconds 10 through 6) are higher pitched than the final five beeps (seconds 5 through 1). The watch emits a longer beep to signal when the countdown reaches zero. � The countdown end beeper always sounds, regardless of the on/off status of the progress beeper. Progress Beeper The progress beeper actually includes two beepers: a reset time beeper and a reset period progress beeper. � The reset time beeper and reset period progress beeper sound only while the progress beeper is turned on.

4. Press A to exit the setting screen. � See �Power Saving Function� for details about configuring Power Saving settings. � The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is applied in all modes. � The day of the week is automatically displayed in accordance with the date (year, month, and day) settings.

Countdown Timer
Minutes Seconds

The countdown timer can be set within a range of one minute to 60 minutes. An alarm sounds when the countdown reaches zero. The countdown timer has two modes: auto-repeat and elapsed time, and a progress beeper signals the progress of the countdown. All of this makes the countdown timer a valuable tool for timing the start of a yacht race. � All of the operations in this section are performed in the

Reset Time Beeper The reset time beeper is similar to the countdown end beeper. When the progress beeper is turned on, the watch beeps each second of the final 10 seconds before the countdown reaches the reset time. Reset Period Progress Beeper The reset period is the portion of the countdown between the reset time and zero. When the progress beeper is turned on, the watch emits four short beeps at the top of each minute during the reset period, and 30 seconds before the end of the countdown.

Countdown Timer Examples
Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Auto-repeat; Progress beeper: On
Reset Period Start Time Reset Time 4'00"
Reset Period Progress Beeper

Timekeeping Mode time

Countdown Timer Mode, which you enter by pressing C.

Countdown End Beeper

Configuring the Countdown Timer
The following are the settings you should configure before actually using the countdown timer. Countdown start time and reset time Timer mode (auto-repeat, elapsed time) Progress beeper on/off � See �To configure the countdown timer� for information about setting up the timer. Reset Time You can set a �reset time�, which is a kind of alternate countdown start time you can recall with the press of a button any time a countdown operation is in progress.

10'00" 5'00" Reset Time Beeper

3'00"

2'00"

1'00" 0'30" 0'00"

Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Elapsed time; Progress beeper: Off Elapsed time Start Time Reset Time measurement
10'00" 5'00"

Countdown End Beeper

0'00"

L

L

1