PIONEER GM-4300F/XU/UC
Instrukcja Obsługi

Specifications
BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER AMPLIFICATEUR DE PUISSANCE PONTABLE A QUATRE VOIES

ENGLISH

Before Using This Product
Thank you for purchasing this PIONEER product. It is designed to give you many years of enjoyment. PIONEER SUGGESTS USING A PROFESSIONAL INSTALLER DUE TO THE COMPLEXITY OF THIS PRODUCT. Please read all instructions and WARNINGS in this manual before attempting operation. Should you have any questions, contact your nearest Pioneer authorized dealer or installation specialist.

ENGLISH
After-sales service for Pioneer products
Please contact the dealer or distributor from where you purchased the product for its after-sales service (including warranty conditions) or any other information. In case the necessary information is not available, please contact the companies listed below: Please do not ship your product to the companies at the addresses listed below for repair without advance contact.

Power source .......................................................................................................... 14.4 V DC (10.8 V to 15.1 V allowable) Grounding system ............................................................................................................................................ Negative type Current consumption .......................................................................................................... 25 A (at continuous power, 4 �) Average current drawn* .......................................................................................................... 6.5 A (4 � for four channels) 10 A (4 � for two channels) Fuse .......................................................................................................................................................................... 40 A � 1 Dimensions .......................................................................................................... 300 mm (W) � 60 mm (H) � 269 mm (D) [12 in. (W) � 2-3/8 in. (H) � 10-5/8 in. (D)] Weight ........................................................................................................ 3.3 kg (7.3 lbs.) (Leads for wiring not included) Maximum power output ................................................................................................ 80 W � 4 ( 4 �) / 200 W � 2 ( 4 �) Continuous power output .............................................................. 40 W � 4 (at 14.4 V, 4 �, 20 Hz to 20 kHz 0.2% THD) 100 W � 2 (at 14.4 V, 4 �, 20 Hz to 20 kHz 0.8% THD) 50 W � 4 (at 14.4 V, 2 �, 20 Hz to 20 kHz 0.8% THD) Load impedance .......................................................................................................................... 4 � (2 � to 8 � allowable)

CAUTION
Never replace the fuse with one of greater value or rating than the original fuse. Use of an improper fuse could result in overheating and smoke and could cause damage to the product and injury including burns.

WARNING
� Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm. Wash hands after handling. � Always use the special red battery and ground wire [RD-223], which is sold separately. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body. � Do not touch the amplifier with wet hands. Otherwise you may get an electric shock. Also, do not touch the amplifier when it is wet. � For traffic safety and to maintain safe driving conditions, keep the volume low enough so that you can still hear normal traffic sound. � Check the connections of the power supply and speakers if the fuse of the separately sold battery wire or the amplifier fuse blows. Detect the cause and solve the problem, then replace the fuse with another one of the same size and rating. � To prevent malfunction of the amplifier and speakers, the protective circuit will cut the power supply to the amplifier (sound will stop) when an abnormal condition occurs. In such a case, switch the power to the system OFF and check the connection of the power supply and speakers. Detect the cause and solve the problem. Contact the dealer if you cannot detect the cause. To prevent an electric shock or short-circuit during connection and installation, be sure to disconnect the negative (�) terminal of the battery beforehand. Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Be sure to protect all cables and important equipment such as fuel lines, brake lines and the electrical wiring from damage. DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result.

CAUTION
Diagram A - Proper
8 8 + � Speaker L+ Pioneer Amplifier 4 � Bridged Mode RL+ Pioneer Amplifier 2 � Bridged Mode +�Speaker

Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the user�s right to operate the equipment.

Owner�s Manual

(Bridge connection: 4 � to 8 � allowable) Frequency response ............................................................................................................ 10 Hz to 50 kHz (+0 dB, �1 dB) Signal-to-noise ratio ........................................................................................................................ 95 dB (IHF-A network) Distortion ............................................................................................................................................ 0.01 % (10 W, 1 kHz) Separation ........................................................................................................................................................ 70 dB (1 kHz) Low pass filter ................................................................................................................................ Cut off frequency: 80 Hz Cut off slope: �12 dB/oct

7 U.S.A.
Pioneer Electronics (USA) Inc. CUSTOMER SUPPORT DIVISION P.O. Box 1760 Long Beach, CA 90801-1760 800-421-1404

Diagram B - Improper
4 +�Speaker 4 + � Speaker R-

GM-4300F
Mode d�emploi

Important
The serial number of this amplifier is written on the bottom of the unit. For your own security and convenience, write it down on the enclosed warranty card. Keep the card handy for future reference.

7 CANADA
Pioneer Electronics of Canada, Inc. CUSTOMER SATISFACTION DEPARTMENT 300 Allstate Parkway Markham, Ontario L3R OP2 1-877-283-5901
For warranty information please see the Limited Warranty sheet included with your product.

High pass filter ................................................................................................................................ Cut off frequency: 80 Hz Cut off slope: �12 dB/oct Gain control ...................................................................................................................................... RCA: 400 mV to 6.5 V Speaker: 1.6 V to 26 V Maximum input level / impedance ........................................................................................................ RCA: 6.5 V / 22 k� Speaker: 26 V / 40 k� Power output ........................................................................................ 40 W RMS � 4 channels (4 � and 1 % THD+N) 100 W RMS � 2 channels (4 � and 1 % THD+N)

PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC. P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: (03) 9586-6300 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901 PIONEER ELECTRONICS DE MEXICO, S.A. de C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270

50 W RMS � 4 channels (2 � and 1 % THD+N) Signal-to-noise ratio ............................................................ 80 dBA (Reference: 1 W into 4 �)

Product registration
Visit us at the following site:

Note:
� Specifications and the design are subject to possible modification without notice due to improvements.

*Average current drawn
� The average current drawn is nearly the maximum current drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.
Published by Pioneer Corporation. Copyright © 2006 by Pioneer Corporation. All rights reserved. Publication de Pioneer Corporation. Copyright © 2006 Pioneer Corporation. Tous droits de reproduction et de traduction réservés. Printed in China Imprimé en Chine

1 Register your product. We will keep the details of your purchase on file to help you refer to this information in the event of an insurance claim such as loss or theft. 2 Receive updates on the latest products and technologies. 3 Download owner�s manuals, order product catalogues, research new products, and much more.

Do NOT install or use your Pioneer amplifier by wiring speakers rated at 4 � (or lower) in parallel to achieve a 2 � (or lower) bridged mode (Diagram B). Amplifier damage, smoke, and overheating could result from improper bridging. The amplifier surface could also become hot to the touch and minor burns could result. To properly install or use a bridged mode for a two-channel amplifier and achieve a 4 � load, wire two 8 � speakers in parallel with Left + and Right � (Diagram A) or use a single 4 � speaker. For a four-channel amplifier, follow the speaker output connection diagram for bridging as shown on the back of your amplifier, and wire two 8 � speakers in parallel to achieve a 4 � load or use a single 4 � speaker per channel. If you have any questions or concerns, please contact your local authorized Pioneer dealer or call Pioneer customer service.

� �

�

�

<KMINX> <06I00000>

<YRD5086-A/U> UC