PIONEER GM-X562/XR/ES
Instrukcja Obsługi

Connecting the Unit
Connecting the Speaker wires
The speaker output mode can be two-channel (stereo) or one-channel (mono). Connect the speaker leads to suit the mode according to the figures shown below.
� Do not connect both the RCA input and the speaker input at the same time.

Installation
CAUTION
� Do not install in: �Places where it could injure the driver or passengers if the vehicle stops suddenly. �Places where it may interfere with the driver, such as on the floor in front of the driver�s seat. � Make sure that wires are not caught in the sliding mechanism of the seats, resulting in a short-circuit. � Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Protect all cables and important equipment such as fuel lines, brake lines and electrical wiring from damage. � Install tapping screws in such a way that the screw tip does not touch any wire. This is important to prevent wires from being cut by vibration of the car, which can result in fire. � To prevent electric shock, do not install the amplifier in places where it might come in contact with liquids. � To ensure proper installation, use the supplied parts in the manner specified. If any parts other than the supplied ones are used, they may damage internal parts of the amplifier, or they may become loose causing the amplifier to shut down.

Specifications
Example of installation on the floor mat or on the chassis
1. Place the amplifier where it is to be installed. Insert the supplied tapping screws (4 � 18 mm) into the screw holes. Push on the screws with a screwdriver so they make marks where the installation holes are to be located. 2. Drill 2.5 mm diameter holes at the point marked, and install the amplifier, either on the carpet or directly to the chassis.
Tapping-screws (4 � 18 mm) Power source .............................................................................................................. 14.4 V DC (10.8 � 15.1 V allowable) Grounding system ............................................................................................................................................ Negative type Current consumption ........................................................................................................ 16.4 A (at continuous power, 4 �) Average current drawn* ............................................................................................................ 5.3 A (4 � for two channels) 7.4 A (4 � for one channel) Fuse .................................................................................................................................................................................. 25 A Dimensions ........................................................................................................................ 279 (W) � 61 (H) � 237 (D) mm Weight ...................................................................................................................... 3.8 kg (Leads for wiring not included) Maximum power output .................................................................................................................... 130 W � 2 / 300 W � 1 Continuous power output .......................................................... 65 W � 2 (at 14.4 V, 4 �, 20 � 20,000 Hz, 0.08% THD) 150 W � 1 (at 14.4 V, 4 �, 20 � 20,000 Hz, 0.8% THD) 75 W � 2 (at 14.4 V, 2 �, 20 � 20,000 Hz, 0.8% THD) Load impedance ............................................................................................................................ 4 � (2 � 8 � allowable) (Bridge connection: 4 � 8 � allowable) Frequency response ............................................................................................................ 10 � 50,000 Hz (+0 dB, �1 dB) Signal-to-noise ratio ........................................................................................................................ 100 dB (IEC-A network) Distortion ............................................................................................................................................ 0.008% (10 W, 1 kHz) Separation ........................................................................................................................................................ 60 dB (1 kHz) Low pass filter ................................................................................................................................ Cut off frequency: 80 Hz Cut off slope: �12 dB/oct Maximum input level/impedance .................................................................................... RCA: 6.5 V/22 k� (0.4 � 6.5 V) Speaker: 26 V/40 k� (1.6 � 26 V)

Two-channel mode (stereo)

(Right) Speaker (Left)

Note:
� Specifications and the design are subject to possible modification without notice due to improvements.

One-channel mode (mono)

To prevent malfunction
� To ensure proper heat dissipation of the amplifier, be sure of the following during installation. �Allow adequate space above the amplifier for proper ventilation. �Do not cover the amplifier with a floor mat or carpet. � Do not install the amplifier near a door where it may get wet. � Do not install the amplifier on unstable places such as the spare tire board. � The best location for installation differs with the car model and installation location. Secure the amplifier at a sufficiently rigid location. � Make temporary connections first and check that the amplifier and the system operate properly. � After installing the amplifier, confirm that the spare tire, jack and tools can be easily removed.

*Average current drawn
� The average current drawn is nearly the maximum current drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers. Floor mat or chassis Drill a 2.5 mm diameter hole

Speaker (Mono)