|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Instrukcja Serwisowa jest kompletna i czytelna. Dziękuję!
 ;
Wszystko OK!
Dokumentacja jest czytelna.
Dziękuję.
;
Bardzo dobra jakość skanu, przystępna cena. Instrukcja serwisowa okazała się przydatna przy "reanimowaniu" dwudziestoparoletniego decka, który teraz pięknie gra :)
;
...instruction is ok.
...instrukcja jest ok.
Thanks/Dzięki
;
Documentation made available quickly and It is good quality. Thanks.
3. Mode: Playback
test tape P-4-A100 (10kHz, �10dB) main board CN302 Pin 1 (L-ch) Pin 2 (GND) L set R
oscilloscope
normal speed. 6. Adjust RV1002 of the LEAF SW board so that the reading of the frequency counter becomes 3000 ± 90 Hz. 7. Press the "/1 button, after the turned ON. 8. Insert the WS-48B into deck A, and insert the normal tape into deck B. 9. Press the SYNC REC button and display "TAPE A t B HIGHSPEED" and then press the REC button to start recording. 10.Press the x button. 11.Press the H button of deck B and check the reading of frequency counter becomes 3000 ± 90 Hz. Adjustment Location: LEAF SW board Sample Value of Wow and flutter W.RMS (JIS) less than 0.3% (test tape: WS-48B)
Pin 3 (R-ch) Waveform of oscilloscope
in phase
45° good
90°
135°
180° wrong
Playback Level Adjustment (Deck A, Deck B) Procedure: Mode: Playback Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301 (L-CH) and RV401 (R-CH) so that adjustment within the following adjustment level. Adjustment level: CN302 playback level: 301.5 to 338.3 mV (�8.2 to �7.2 dB) level difference between the channels: within ± 0.5 dB Adjustment Location: AUDIO board
4. After the adjustments, apply suitable locking compound to the parts adjusted. Adjustment Location: Playback Head (Deck A) Record/Playback/Erase Head (Deck B)
test tape P-4-L300 (315Hz, 0dB) set
level meter
Reverse
Foward
main board CN302 Pin 1 (L-ch) Pin 3 (R-ch)
Tape Speed Adjustment (Deck A) Note: Set the test mode using the following method and begin tape speed adjustment. In the test mode, the speed will switch to double speed or normal speed each time the HIGH-SPEED CD-MD SYNC button is pressed. Procedure: With the power turned ON, press the x button, DISPLAY button, and DISC 3 button simultaneously. (The �VOLUME� on the fluorescent display tube will blink while in the test mode.) To exit the test mode, press the "/1 button. 1. Insert the WS-48B into deck B. 2. Press the H button of deck B. 3. Press the HIGH-SPEED CD-MD SYNC button and play the tape at double speed. 4. Adjust RV1001 of the LEAF SW board so that the reading of the frequency counter becomes 6000 ± 180 Hz. 5. Press the HIGH-SPEED CD-MD SYNC button and play the tape at Adjustment Location [LEAF SW BOARD]
RV1001(High Speed) RV1002(Normal Speed)
RV1002
RV1001
34
|
|
|
> |
|
