Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 6041 gości i 
2 zarejestrowanych klientów 
Kategorie
Informacje
Polecamy
Strona główna >> WHIRLPOOL >> HD1000XSW7 Instrukcja Obsługi
 
 0 szt. w koszyku 

WHIRLPOOL HD1000XSW7
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis WHIRLPOOL HD1000XSW7 Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 11 (kliknij aby zobaczyć)
Caring For Your Hot Water Dispenser
Energy-saving tips and preparation for periods of nonuse
On average, you will use your hot water dispenser to heat 7 to 8 cups of water per day. This uses only 19 kilowatt-hours of energy per month. So it is Not necessary to turn off the hot water dispenser each night to conserve energy. However, if the hot water dispenser will not be used for an extended period of time, follow these instructions:

For short periods (2-30 days of nonuse):
Set the Temperature Control to the �Off� position to conserve energy.

For long periods of nonuse (winterizing, seasonal storage or protection from freezing):
1. Turn Temperature Control to the �Off� position. 2. Unplug hot water dispenser power supply cord.
O-ring screw

When ready to use the dispenser again, follow Installation Instruction Steps 14-16, Page 9. Do Not Turn Unit On If Tank Is Empty. Damage to the unit will result and is not covered by the warranty.

3. Turn On/Off Cap, hold and run water until water is cold. 4. Turn saddle valve handle clockwise to turn off water supply. 5. Place a 3-quart minimum container under the drain plug at the bottom of the tank. 6. Use a screwdriver to remove the screw and O-ring from the drain tube. 7. Replace the screw and O-ring in the drain tube opening. Tighten the screw to reseal the drain.

Cleaning the spout screen
If you have very hard water, and you notice that the water flow is reduced, 1. Turn Temperature Control to the �Off� position. Push down and turn On/Off Cap clockwise and run water until it is cold to avoid possibility of burn. 2. Remove the two spout screws. 3. Remove spout base plate. 4. Pull the screen assembly out of the hot water tube. it may be necessary to clean the spout screen. 5. Use a small brush and vinegar to remove hard-water deposit. If deposit has hardened, soak in vinegar for an hour or two. Then use a brush to clean. 6. Replace screen assembly in tube. Reattach plate back onto spout. 7. Turn Temperature Control to the �Max� setting. The dispenser will be ready in about 15 minutes.
11

screws

base plate

Klienci kupując ten produkt kupili także


Za darmo!

HD1000XSW7 WHIRLPOOL
Instrukcja Instalacji

Kompletna instrukcja instalacji urządzenia w formie pliku PDF.Po zakupieniu tej instrukcji wyślemy…

$4.99

HD1000XSW7 WHIRLPOOL
Katalog Części

Katalog części w formie pliku PDF. Plik zawiera wykaz części znajdujących się w urządzeniu wr…
>
Parse Time: 0.177 - Number of Queries: 103 - Query Time: 0.041