PHILIPS HQ42/15
Instrukcja Obsługi

ENGLISH
Important Read these instructions for use carefully before using the appliance and save them for future reference. � � � Keep the appliance and the mains cord dry (fig. 1). Do not use a damaged mains cord. If the mains cord is damaged, always have it replaced by one of the original type in order to avoid a hazard. Store and use the appliance at a temperature between 5cC and 35cC.
. .

4222 002 42775

Using the appliance Shaving

.

1 Switch the appliance on by pressing the switch lock and pushing the on/off slide upwards (fig. 6). The switch lock prevents accidental switching on of the appliance. 2 Move the shaving heads quickly over your skin, making both straight and circular movements (fig. 7). Shaving on a dry face gives the best results. Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system. 1 Switch the shaver off by pushing the on/off slide downwards. 2 Put the protection cap on the shaver every time you have used it, to prevent damage (fig. 8). Cleaning and maintenance Regular cleaning guarantees better shaving performance. Every week: shaving unit and hair chamber 1 Switch the shaver off, remove the mains plug from the wall socket and pull the appliance plug out of the shaver. 2 Clean the top of the appliance first, using the brush supplied (fig. 9). 3 Press the release button (1) and remove the shaving unit (2) (fig. 10). 4 Clean the inside of the shaving unit and the hair chamber with the brush (fig. 11). 5 Put the shaving unit back onto the shaver. Every two months: shaving heads 1 Switch the shaver off, remove the mains plug from the wall socket and pull the appliance plug out of the shaver. 2 Press the release button (1) and remove the shaving unit (2) (fig. 10). 3 Remove the retaining frame by pushing the sides of the central spring towards each other (1) and lifting the retaining frame out of the shaving unit (2) (fig. 12).
.

4 Slide the shaving heads out of the retaining frame and clean them one by one (fig. 13). Do not mix up the cutters and the guards. This is essential since each cutter has been ground with its corresponding guard for optimal performance. If you accidentally mix the sets up, it could take several weeks before optimal shaving performance is restored. 5 Clean the cutter with the short-bristled side of the brush (fig. 14). Brush carefully in the direction of the arrow. 6 Brush the guard (fig. 15). 7 Slide the shaving heads back into the retaining frame and put the retaining frame back into the shaving unit (fig. 16). 8 Put the shaving unit back onto the shaver. � For extra thorough cleaning, clean the shaving heads by putting them in a degreasing liquid (e.g. alcohol) every six months. To remove the shaving heads, follow steps 1 to 4 described above. After cleaning, lubricate the central point on the inside of the guards with a drop of sewing machine oil to prevent wear of the shaving heads (fig. 17). Storage �
.

�

Inserting batteries The appliance runs on two R6 AA 1.5-volt batteries. Preferably use Philips alkaline batteries. Make sure that your hands are dry when inserting the batteries. 1 Remove the lid of the battery compartment (fig. 2). 2 Place two batteries in the battery compartment (fig. 3). Make sure the + and - indications on the batteries match the indications in the battery compartment. The shaver does not work if the batteries have been placed incorrectly. 3 Put the lid of the battery compartment back onto the appliance. First insert the top part of the lid (1) and then press the bottom part down until you hear a click (2) (fig. 4). � To avoid damage due to battery leakage: do not expose the appliance to temperatures higher than 35cC; remove the batteries if the appliance is not going to be used for a month or more; do not leave empty batteries in the appliance. Cordless shaving time Two new batteries offer a cordless shaving time of 60 minutes. Mains operation You can also shave without batteries by connecting the shaver to the mains. 1 Put the appliance plug in the shaver (fig. 5). 2 Put the mains plug in the wall socket.

Put the protection cap on the shaver to prevent damage (fig. 8). Replacement
.

Replace the shaving heads every two years for optimal shaving results. Replace damaged or worn shaving heads with HQ4« Philips shaving heads only. 1 Switch the shaver off, remove the mains plug from the wall socket and pull the appliance plug out of the shaver. 2 Press the release button (1) and remove the shaving unit (2) (fig. 10). 3 Remove the retaining frame by pushing the sides of the central spring towards each other (1) and lifting the retaining frame out of the shaving unit (2) (fig. 13). 4 Slide the shaving heads out of the retaining frame (fig. 14). 5 Slide new shaving heads into the retaining frame (fig. 16). 6 Put the retaining frame back into the shaving unit (fig. 18). 7 Put the shaving unit back onto the shaver.
2/6