|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 ;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.
NUDOS NiMH shavers
HQ4850 The green LED �+� goes on. If the cells are almost empty the red LED �-� will go on as well. When the red LED goes out, there is enough capacity for one cordless shave of approx. 3 minutes. After 60 minutes the green LED starts to blink, to indicate that the cells are full. The signals during shaving are described under �ALL�. HQ3870 + HQ4870 One of the LEDs of the capacity indicator will start to blink. If the cells are almost empty, the block �20� will be red. When it turns green, there is enough capacity for one cordless shave. Each time when another 20 % of the full charge has been reached, the next block of the indicator will start to blink. After 60 minutes, the �100� block starts to blink. This LED stops to blink as soon as shaver is fully charged. If charging is continued (in the 25 mA mode now), the IC will force the PM to supply 1000 mA for half a sec. every 10 secs to compensate for the continuous burning of the LEDs. When switching on and off, the actual capacity is shown for approx. 8 seconds. After shaving cordless with a fully charged shaver for some time, the �100� LED will be no longer visible. Then, the other blocks will gradually disappear one by one. The next signal is described under �ALL�. HQ4890 The green LED goes on and one segment of the LCD will start to blink. If the cells are empty, this will be the �20� segment. The red LED will remain on until there is enough capacity in the cells for one cordless shave of approx. 3 minutes. Each time when another 20 % of the full charge has been reached the next segment will start to blink. After 60 minutes the word �FULL� and the green LED start to blink. When shaving cordless with a fully charged shaver, first �FULL� will disappear. After some time the �100� segment will disappear, etc. Finally, a blinking �20� segment will show together with the red LED, as described below. ALL During discharging the capacity counter counts down proportional to the motor current. When the counter reaches the �zero� state, a Nearly Empty Indication (NEI) is given by the red LED. After the shaver has been switched off the red LED will blink for 4 seconds. If the shaver is not in use, the counter will count down at a slow rate during approx. 100 or 200 days, to compensate for the self-discharge of the cells and the power consumption of the ICs (100 days at Tamb>35�C, 200 days at Tamb<35�C). HQ 4850
12345 12345
3
TS20 SK1 R36 R26 1 6 9 R34 R21 R22 13 14 15 16 5 C23 12 17 18 19 11 R33 7 IC2 10 D22 SAA 1500T 20 D21 R25 28
R35
R27
D9
4 3
C21
C22
TS20 SK1 R36 R26
R35 6 R34 R21 R22 3 C21 C22 5 C23 12 4
1
28 9
R27
D9
R25 13 14 15 16 17 18 19 11 20 IC2 10 D20 D25 D24 D23 D22
R33 7 SAA 1500T
HQ 3870/HQ 4870
12345
TS20 SK1 R36 R26 R35 6 R34 R21 R22 4 3 C21 C22 5 12 9 13 14 15 16 17 18 19 R33 11 7 IC2 20 10 D21 D22 LCD 1 28 R27 R25 D9
C23
SAA 1500T
HQ 4890
PCS 99 109
|
|
|
> |
|
