|
|
|
Kategorie
|
|
Informacje
|
|
Polecamy
|
|
|
 |
|
|
Dla tego produktu nie napisano jeszcze recenzji!
 ;
Dobrej jakości skan - wkońcu mogłem poznać wszystkie funkcje tego odtwarzacza - polecam .
;
Gruba instrukcja - poprostu wszystko co potrzreba - polecam .
25
TimeScan
Names of special-effects playback Speed SP Speed LP Audio output Search -9x -7x -5x -3x -7x -3x Reverse Play -1x Slow-Motion -1/6x -1/18x -1/6x -1/18x Audio is not output. *Still 0 0 Audio is output. Slow-Motion 1/18x 1/18x 1/6x 1/6x Forward Play 1x 1x Search 2x 3x 5x 7x 9x 2x 5x 9x
Audio is output.
Audio is not output.
Audio is output.
** To activate the Still mode from the remote control press PAUSE button. Still mode cannot be engaged using the remote control's @ # button. � Noise tends to appear at -9x or 9x normal speed during TimeScan search. If noise appears or the picture is distorted, press and adjust tracking with TV PROG + or � button. When the playback speed is changed, adjust tracking again. � The speed is shown during TimeScan in the upper right corner of the TV screen for approx. 5 seconds. (On some TVs the display may be distorted.) � To resume normal playback, press PLAY. � When using the recorder's TIME SCAN SHUTTLE ring, the playback speed may not change in the correct step if it is turned too fast. � Picture and audio may occasionally become distorted when the recording speed changes. If this happens, resume normal playback once, and then try using TimeScan again. � The picture may be noisy or there may be a loss of colour when you change the playback speed. (More noise will appear with LP recordings.) � Noise may appear or the upper part of the picture may be distorted during still, frame-by-frame playback, 2x search of LP recordings, or with certain tapes. � Picture may appear distorted in comparison to normal playback. � When normal playback resumes from search (including TimeScan), still, slow motion or frame-by-frame playback, the picture may jitter vertically momentarily depending on the type of TV being used. � Depending on the tape in use, noise may appear or the upper part of the picture may be distorted. � In TimeScan mode there will be a time lag between the video and the audio and noise may appear in the audio signal. � TimeScan sound quality will differ in comparison to normal playback. � When material such as music videos where there is non-stop sound (very few breaks in the soundtrack) are viewed at 2x normal speed, the audio playback may be faster than normal. � When the playback direction is reversed, it takes approximately 6 seconds until sound is heard. � TimeScan does not work with NTSC playback.
If you don't want to hear TimeScan audio, set the "TIME SCAN AUDIO" to OFF. (See below)
TimeScan Audio
The audio output can be set ON/OFF during TimeScan. Select ON/OFF as required. * The default setting is "ON". 1 Press MENU to access the Main Menu screen. 2 Move the highlight bar (pointer) to "MODE SET" by pressing %�, then press OK or #. 3 Move the highlight bar (pointer) to "TIME SCAN AUDIO" MODE SET by pressing %�, then press OK or # to select "ON" or "OFF".
B. E. S. T. ON PICTURE CONTROL AUTO AUTO TIMER OFF O. S. D. ON DIRECT REC ON AUTO SP=LP TIMER OFF POWER SAVE OFF NEXT PAGE [5�] = [MENU] : EXIT
PREVIOUS PAGE AV2 SELECT TIME SCAN AUDIO
AV2 ON
[5�] = [MENU] : EXIT
4 Press MENU to return to the normal screen.
|
|
|
> |
|
