Check that you have all the accessories.
STANDBY/ON MUTE
2
SLEEP STATUS DIMMER
TUNER EDIT
Put the batteries in the remote control and stick the non-skid pads to the base of the speakers. 1
Open the battery compartment on the rear of the remote control.
3
Connect each speaker to the receiver using the supplied speaker wires.
To connect, insert the colored wire into the matching colored (+) tab and the other wire into the black (�) tab as shown below. Connect the center speaker the same way (matching the wire the color-coded label). Note that the color-coded tabs are as follows:
� Red : Front right speaker � White : Front left speaker � Green : Center speaker � Purple : Subwoofer � Grey : Surround right speaker � Blue : Surround left speaker
Surround right
Surround left
Speaker cord (x1)
INPUT SELECTOR DIGITAL STB DVD/DVR FM/AM TAPE/VCR TV
CLASS
�
TUNING
+ +
�
STATION
+
2
Insert the supplied batteries following the markings inside the battery compartment to align them correctly.
SYSTEM SETUP
VOLUME
CH LEVEL
FM wire antenna
ROOM SETUP
ENTER
TEST TONE
�
AUTO
OFF
SURROUND
SOUND TONE
STEREO MPX
3
Replace the battery compartment cover.
Receiver
Batteries (x2)
�
BASS
+
�
TREBLE +
4
RECEIVER
AM loop antenna
Remote control Brackets (x4)
Stick the self-adhesive non-skid pads to the underside of each speaker, and to the underside of the subwoofer. Use four pads per speaker (see below).
Listening position
SPEAKERS
+ �
R
FRONT
L
SUB CENTER WOOFER
SURROUND R L
+ �
Subwoofer
Screws (x4) Non-skid pads (1x20, 1x4)
You should also have: � Speakers (x5) � Subwoofer � Operating instructions � Warranty card
Front and surround speakers Center speaker Subwoofer
For the best surround sound, set up your speakers like this. The front left and right speakers should be about 6�9 feet apart.
Front right
Center
Front left
4
1 2
Connect antennas
Connect the FM wire antenna and fully extend along a window frame or another suitable place that gives good reception. To connect the AM loop antenna, twist the exposed wire strands together and insert into the terminal, then snap the connector shut as shown below.
5
1 2
Connect the receiver to your DVD player/ recorder.
6
1
Press
Use a coaxial digital cord (not supplied) to connect the digital output of your DVD player/ recorder to the DIGITAL INPUT (COAXIAL) DVD/DVR jack. Use a red/white stereo audio cord (not supplied) to connect the AUDIO TV IN jack on the receiver to the audio output on your TV.* This will allow you to listen to your TV through this speaker system.
Plug the receiver, DVD player/ recorder and TV into a convenient AC outlet.
STANDBY/ON to switch on the receiver.
7
After switching on, make any necessary settings required by the DVD player/ recorder, then you're ready to start enjoying your home theater system.
Refer to the receiver's operating instructions for a detailed explanation of this system's surround sound features.
STANDBY/ON
AM loop antenna
* Note that you must also connect the DVD player/ recorder's video output to your TV's video input to watch a DVD video (video cable is not supplied).
STANDBY/ON
VOLUME
AUTO
SURROUND
STEREO
INPUT SELECTOR DIGITAL STB DVD/DVR
+
FM/AM TAPE/VCR TV
�
Receiver
DIGITAL INPUT (COAXIAL) DVD/DVR
FM wire antenna
Receiver
TV IN IN AUDIO
2
+ +
L
Switch on your DVD player/ recorder and TV, and set the TV to the correct video input.
ANTENNA
OUT R
�
�
FM UNBAL 75� AM LOOP
VIDEO 1
Receiver
STANDBY/ON
VIDEO SELECT
TV
R VIDEO IN AUDIO OUT L
TV
STANDBY/ON
3/8 in. (10mm)
DVD player/ recorder
DIGITAL OUT
VIDEO OUT
DVD player/ recorder
For detailed instructions, see the Operating Instructions supplied and / or contact one of our knowledgeable Pioneer Customer Service Representatives at 1 - (800) 421-1404.
